Jump to content
Ultimate Subaru Message Board

OK, so the new engine is in, but I messed up the electrical


Abue
 Share

Recommended Posts

1994 Subaru Loyal Wagon

 

New Clutch, new engine block, new gaskets, new radiator, new hoses, and such....

 

But now, (And I have charged the battery) when I turn the key, everything shorts out, and I lose all power.

 

Until I turn the ignition, I have power, then I turn the key and I have to disconnect and reconnect the battery to get power again.

 

No blown fuses, in the fuse box, all the fusible links are fine.

 

HELP!!!

 

-Rob

 

(I am in Mt. View CA, if anyone is local and can give me a hand, it would be much appreciated)

Link to comment
Share on other sites

OK, just got back in from messing with it. Gaaaa..

 

When the starter is in the car, the whole things shorts out. When it is out of the car, it doesn't spin or move at all. I think it is hosed. That sux. Any input would be a huge help.

 

-Rob

Link to comment
Share on other sites

Rob it sure sounds like the positive cable and the negative cable are backward on the starter.

There is a bolt on the back of the starter,

this big cable must run to the + terminal of the battery.

Could by chance you have this connected to the negative terminal?

Please have another look at it and reply

Link to comment
Share on other sites

does it just click or does it draw alot of current? The solenoid contacts go bad, preventing the starter motor from engaging. What can also happen is a bad spot on the armature, and if it stops on that spot it wont move again until you rotate it past manually. Try pounding on it with a hammer while you've got current through it, or rotating it then trying it, to see whether these are the problems.

 

wait I read more, it does sound like shorting out, so that would likely rule out what i said above

Link to comment
Share on other sites

The crazy thing is that I did't touch the starter when we did the swap. This is why I am so confused. If I can't figure it out by Wednesday, I think I am going to give up and take it to the dealership. Grrrr...

 

-Rob.

Link to comment
Share on other sites

The only time this has ever happened to me (and it has happened a few times) is when I am working on a car and not bothered to tighten the bolts holding the cables to the battery posts. When you attempt to engage the starter, it draws so much current that one of the terminals often arcs out. Moving the cable will get a good enough connector to get dash lights, etc., but you will lose it again if you try to start the engine again.

Make sure the battery terminals are clean and the connectors are on REALLY TIGHT.

Good Luck!

-Louis-

'91 Loyale 4wd 5spd Wagon

Link to comment
Share on other sites

  • 1 month later...

Ahh the project that seems to go on forever...

 

 

Long story short, I can't get it to start. The starter is turning the engine, I am getting a spark. I took off the distributor, rotated cylinder 1 to TDC and then to B20, then replaced the distributer. (aligned the little hole)

 

The starter turns over the engine, and then NADA. I think there is fuel getting in. (I smell it.) And this Chilton book I have is ALL BUT FRIGGEN USELESS!

 

HELP!

Link to comment
Share on other sites

Hellloooooo Tribe member (happy grin)

 

I wonder *IF* you have seen the specific threads about the vagueness that are Chiltons' manuals for "timing the engines" of our subarus.

 

the book (correct me where i am wrong folks) misses a step entirely for Chilton where the FSM describes much better.

 

The starting situation with the from Cam covers off to see the "hole/notch" in the cam wheels.... drivers side "hole" in cam needs to be at TDC on the notch in the cam cover backplate *With the flywheel at 0 degrees* IIRC

 

THEN tuyrn the crank 360 degrees and then****

then you turn the crank untill the passenger side Cam "hole" is lined up with the notch at TDC (AKA 12 O'clock) this is EA82 correct alightment and then you can look in the #1 cyl for adjusting the TDC of the piston is carrectly matched and then drop in the dizzy for buttoning it all up....

 

 

did i screw up you train of though Abue?

 

take care..... I'm off to Florida for a week with Gramma and the two great aunties.....

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

×
×
  • Create New...