Jump to content
Ultimate Subaru Message Board

80 gl passing light


Recommended Posts

:popcorn::drunk: Alright now I can help here I"m pretty sure I"ll be right back! I need more:drunk:+:popcorn: +smokes! Be back after this BRIEF intermission ;)

:D I"m good now-cigs:drunk: And the bible"s-Car Books:) I have the 3rd eye blind car [YES the LIGHT WORKS!:banana:] But It"s in Delta,Co. So I can"t look at it:( SO to the bible 1978-83 motor wiring MANUAL:brow: Now I know the 3rd light only works on high beam with the center light switch in [it"ll be lit up] Well :banghead: this book has every wire in the car except the 3-4wires for the center lamp [it"s name]:horse: It has the vin.#"s body descript.w/mtr.but not ONE Stupid light!!! I"ll have to go dig up the factory shop manual now:( I haven"t looked at it in a while HMMMM I wonder why.....Let ME think a min:-\ OH NOW I know....My hatchie doesn"t break down:D:banana:!! I"m gonna go dig for the other Bible now!! Worse case I"ll look at the 81 when I go to Delta Fri. Nate

Link to comment
Share on other sites

if you have to wire it like i did its going to take a while because mine didn't come factory with it so i had to wire the whole thing but now i can run mine without headlights:D

NICE!!! I"m going to do that to my 81 I think it"s cool to drive around in the mtns. at night with just the light in frt.:brow: All stealth!!

Link to comment
Share on other sites

Ok here's my soldering job

8E2FFB9A-C389-4C31-9EE2-F8A479424A3B-8174-000008612D3C16A9.jpg

And here is a pic of the whole unit

802ADA6F-9DC6-4515-8EE9-F0E9D4DDB8DB-8174-0000086136A75C38.jpg

Now all I need to do is use a little electircal tape around the harness and it'll be ready to install. Next i will have to see if I have to replace the relay, I think it got fried when someone tried to turn the light on when it was seized up.

Edited by mikaleda
Link to comment
Share on other sites

It's noit just the switch. there is a relay too. Located near the battery.

 

If it's bad.....there is a write up in the old USRM about using a DPDT switch, or a DPDT relay run by the factory switch.

 

with switch:

http://www.indysworld.com/80s/general/USRM/3rdEye/using_center_light_w.htm

 

with relay:

http://www.indysworld.com/80s/general/USRM/mick-usrm/electrical/centerlamp-relay.pdf

Thank you gloyale that information is coming in handy I think I am going with the relay option but I am tempted to go with the switch since I already have one.

Link to comment
Share on other sites

Ok here's my soldering job

8E2FFB9A-C389-4C31-9EE2-F8A479424A3B-8174-000008612D3C16A9.jpg

And here is a pic of the whole unit

802ADA6F-9DC6-4515-8EE9-F0E9D4DDB8DB-8174-0000086136A75C38.jpg

Now all I need to do is use a little electircal tape around the harness and it'll be ready to install. Next i will have to see if I have to replace the relay, I think it got fried when someone tried to turn the light on when it was seized up.

:cool: I"ve had quite a few of the 3rd eye blind cars:headbang::headbang::D!!I"ve bought cars from people and they"ve asked me {what does that switch do?} If it works I show them and they think its cool!! Now to fix yours so it doesn"t get messed up later:brow: Nice solder job:) Now clean up around what you did with a wire brush cover it with ult.blk. silicone-keeps it from corroding-now at the plug inside it fill it up with dielectiric grease so it doesnt corrode-now on the outside cover all the wire openings w/silicone for the same reason:D Good luck!

Link to comment
Share on other sites

I was thinking the same thing defiantly don't want it corroding again.

Update: well I plugged in my newly rewired light and the light came on but the door didn't move. I think the relay is the culprit, I think when they tried to turn the light on after it was seized it probably fried that part of the relay.

I am going to buy one of those dpdt relays and wire it in.

Link to comment
Share on other sites

Motor defiantly works.

Ok I went out and wired in a dpdt switch like this http://www.indysworld.com/80s/general/USRM/3rdEye/center-lamp.html

The lamp turns on but the lid doesn't open. So I ran 12 volts to the Motor and it spun the lid open, when I switched it to the off position the lid closed. So I am thinking that the relay is not the problem since the switch did the same thing. Does anyone know what could be causing this?

Link to comment
Share on other sites

you use any of the orignal wire on it? i wired all mine with 12 or 14 gage copper wire. they tend to corrode when there as thin of gage as they are and some of those are aluminum and cheep so they corrode easy. did you make sure you dont have a wire crossed to make the relay click making the motor useless? did you check the ends for corrosion to?

Link to comment
Share on other sites

Well I messed with it all night and it ended up being the wireing harness so I am going to wire in a dpdt switch.

I think the problem was also the colors changed on mine once it got up to the relay, green/ white turned to green/ blue and red turned to green/ red.

Edited by mikaleda
Link to comment
Share on other sites

9BA79423-B681-4952-9C19-7336846C6E17-9062-000009E73D0D4697.jpg

It works!!!

I had to make a wiring harness all the way from the light to the switch I repurposed the endes of the old harness they are good I checked the connections and for corrosion.

I wired the switch like this http://www.indysworld.com/80s/general/USRM/3rdEye/center-lamp.html

Pics below

Harness

068F3CBE-1608-4286-B0D7-3FF2A9ABA762-9062-000009E74E94294F.jpg

I reused the ends off the old harness

D6B278E8-C65A-40DA-92ED-675DBE4D90B8-9062-000009E7262798B6.jpg

I used the power source from the old switch for temporary I will reuse the plug later

51BD4F8A-D641-487E-9CCA-DC77FD5E8A1E-9062-000009E715BC4BE7.jpg

I used sensor safe rtv to seal the solder conections on the motor

AEFEEE3E-0B19-4172-9F92-992E5F39AF24-9062-000009E6B8C390A8.jpg

The rubber plug I used to go through the firewall

714CAD3A-8C2F-474E-BA9B-C3F45BDDE7F5-9062-000009E6E8FB971D.jpg

I ran the harness through the driver side strut tower

CE0C14A7-277D-436E-B5A3-1E22990CACC7-9062-000009E6D814D9AD.jpg

Around the charcoal canister (don't worry it still fits right)

11BFDDDD-7546-441C-A97C-C215CC06A995-9062-000009E6CE2B2DD9.jpg

Ends on the drivers side if the radiator and meets the plug on the light it self

0FEEA4D5-10F7-4BC1-A01F-98A8F65B6A32-9062-000009E6C318CD0B.jpg

FD872C92-1B6B-483D-A2B4-E508A2F3051A-9062-000009E73131036A.jpg

Link to comment
Share on other sites

glad to see you got it to work, looks like you wired it about the same i might make my ends have the end connectors now but i wrapped the whole thing in eletrical tape

 

I was going to wrap the whole thing but I used really nice wire that lasts for a long time it's got a thicker wrap around it, I figured that way if I have to I have access to single wires also

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

×
×
  • Create New...