Jump to content


Welcome to Ultimate Subaru Message Board, my lurker friend!

Welcome to Ultimate Subaru Message Board, an unparalleled Subaru community full of the greatest Subaru gurus and modders on the planet! We offer technical information and discussion about all things Subaru, the best and most popular all wheel drive vehicles ever created.

We offer all this information for free to everyone, even lurkers like you! All we ask in return is that you sign up and give back some of what you get out - without our awesome registered users none of this would be possible! Plus, you get way more great stuff as a member! Lurk to lose, participate to WIN*!
  • Say hello and join the conversation
  • Subscribe to topics and forums to get automatic updates
  • Get your own profile and make new friends
  • Classifieds with all sorts of Subaru goodies
  • Photo hosting in our gallery
  • Meet other cool people with cool cars
Seriously, what are you waiting for? Make your life more fulfilling and join today! You and your Subaru won't regret it, we guarantee** it.

* The joy of participation and being generally awesome constitutes winning
** Not an actual guarantee, but seriously, you probably won't regret it!

Serving the Subaru Community since May 18th, 1998!

Guest Message by DevFuse
 

Photo
- - - - -

Noise When Turning Left


  • Please log in to reply
4 replies to this topic

#1 alaskaloyale

alaskaloyale

    Advanced Member

  • Members
  • PipPipPip
  • 43 posts
  • Fairbanks Alaska

Posted 21 June 2013 - 03:13 PM

I have an 88 GL Wagon, 5spd DR. It makes a very loud rumbling noise that starts at about 25mph and increases in volume with speed. It gets much louder during left turns at higher speeds, and gets quieter or totally silent during right turns. I ordered new wheel bearings, but I'd like to know if I'm likely to need any other parts before I start tearing the hubs off my daily driver. Any input would be appreciated :)

#2 92_rugby_subie

92_rugby_subie

    Subaru Master

  • Members
  • 1,990 posts
  • Hillsboro OR

Posted 21 June 2013 - 05:16 PM

Well, in my post: http://www.ultimates...with-questions/

 

I experienced needing new tie-rods when I had mine apart...

 

Hows your bank account? Id definitely plan on doing the wheel bearings, 6207 2RS C3 bearings are a great deal if you don't wanna get messy with grease (youll want a little bit anyway though, makes axle slide easier.

 

With the noise, Id replace wear items... ball joint, wheel bearings, axle nut and cone washer, feel your tie-rod next time you have a chance, if it feels loose, replace it.

As for materials, youll want some kind of grease/lubricant, itll make it a lot easier to slide the axle in the hub, make sure to clean all your surfaces before applying grease. Youll need new seals, inner and outer, perhaps not if you go with sealed bearings but I put mine in there because I figured it couldn't hurt.

 

Check your brakes too, don't want those to fail...

 

Use antiseize lubricant for putting things back together, I use it on the threads of bolts, of the tie-rod, on the inside of the hub that connects to the strut, as well as the strut...


Edited by 92_rugby_subie, 21 June 2013 - 05:18 PM.


#3 Subeast-EA81

Subeast-EA81

    Subaru Junkie

  • Members
  • 132 posts
  • Battle Ground

Posted 22 June 2013 - 07:16 PM

Sounds to me like you have a wheel bearing issue on the right side (think about the transfer of load to that side while cornering) In regards to the bearings them selfs i +1 on sealed bearings, make sure you get a Good brand like Timken SKF, or FAG. These are industrial Bearings and require no Seals (if you order them sealed that is), so i personally wouldn't bother with getting new seals.  Furthermore keep in mind that these are press in press out bearings, so unless you have a press at home you may need a machine shop to install them, (or a couple Sockets, and a Drift) i'll advise against that method as you need to get them in there straight, but it can be done.  since you will be removing the knuckle for this job its best to evaluate the remaining components that Rugby stated in addition to the axle assembly as well (commonly referred to as CV Joints).  Thats my 2 cents hope it helps



#4 alaskaloyale

alaskaloyale

    Advanced Member

  • Members
  • PipPipPip
  • 43 posts
  • Fairbanks Alaska

Posted 22 July 2013 - 08:53 PM

Well, I replaced the passenger-side wheel bearings with FAG-brand sealed units. It cut the amount of total noise the car makes when driving somewhat, and completely eliminted the rattling I heard from that side when I drove with the windows down. Definitely a worthwhile job to do. I did discover while I was in there that the tie rod end and ball joint boots are both cracked, so I am going to need to replace them sometime soon.

 

However, the main noise I was experiencing (that disappears when turning right and gets louder when turning left) did not improve at all. Is it possible that this is from the drivers side wheel bearings, or could it be something else? The drivers side tire is wearing slightly more on the outside than the inside, which makes me think it is a tie rod issue. If you guys could help me shed some light on the issue that would be fantastic. Thanks again for everyone's help and knowledge! :)



#5 AKghandi

AKghandi

    87 GL-10 2" lift 27" tires, 86 GL 2" lift 29"

  • Members
  • 1,161 posts
  • Anchorage, Alaska

Posted 23 July 2013 - 04:59 PM

the tire is wearing more on the outside edge?.. jack up that side and shake the tire. I bet its the drivers side. especially if it gets louder on left turns, all the weight goes to the drivers side. Also if the bearings are that bad, the tire will  camber out on left turns causing wear on the outside of the tire

 

I went through the same thing I thought it was the passenger side so I replaced it... turns out it was the drivers side. its something to do with the double bearings in the knuckles. 

 

 

Also check the hub on the drivers side, it may be the culprit. if the axle nut is loose, or the flat washer is gone it will strip the hub and make noises and tire wear like you describe. make sure the cone washer is in good shape and the hub splines are straight and even.

 

 

there is some shop here in AK that has been doing axles replacements on subarus and completely screwing things up. i got a loyale with 2 brand new axles and both front axle nuts were loose. and one was missing the flat washer..


Edited by AKghandi, 23 July 2013 - 05:05 PM.





0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users