Jump to content
Ultimate Subaru Message Board

Drivetrain Swap?


Recommended Posts

Hello All, 

I have a 1981 4spd 4wd GL wagon with a perfect body and interior and a 1986 5spd 4wd GL wagon with a perfect drivetrain. I would like to know if I can swap the entire drivetrain (front/rear) from the 1986 into the 1981??? Any input would be greatly appreciated. Thanks

Link to comment
Share on other sites

Sure. You will have to pound a dent in the frame rail on the drivers side so the valve cover of the EA82 will clear.

I would recommend just swapping the 5-speed in with your existing EA81 engine, if it's in good shape. You will get a minimal power increase with the EA82, but they come with more issues... Personally, I would rather just put a Weber on the engine you have.

If you really want to upgrade, an EJ22 from an early Legacy fits right in with no pounding  :rolleyes:

 

A lot more involved though...

Link to comment
Share on other sites

+1 I would just swap the tranny and rear diff if necessary. I would NEVER opt to install and EA82 in place of an EA81. Not saying it's a bad motor, but it has many more things that can and will go wrong if you're not vigilant with maintenance. I do not believe pounding a dent in the rail will allow for proper clearance either. Iirc, you can't drop an EA82 into an EA81 body that hasn't been lifted without cutting an welding. Not to mention, if you did somehow manage to shoehorn it in there, now you can't do any valve cover, cam tower or head gasket work to it with the engine in the car. Nope, wouldn't do. Definitely wouldn't do it. Nope. Definitely. Yeah, bad idea. Definitely. lol

  • Like 1
Link to comment
Share on other sites

I did 3 of them like that back in the day, completely stock, no lift. 

 

Had an EA82T in my hatch. Took the front halfshafts out in the summer.   :burnout:

 

But that was when the EA82 was the NEW engine... Oooo... Overhead cams!!   :slobber:

 

The EJ was still just a twinkle in Subaru's eye.

Link to comment
Share on other sites

 Iirc, you can't drop an EA82 into an EA81 body that hasn't been lifted without cutting an welding. Not to mention, if you did somehow manage to shoehorn it in there, now you can't do any valve cover, cam tower or head gasket work to it with the engine in the car. Nope, wouldn't do. Definitely wouldn't do it. Nope. Definitely. Yeah, bad idea. Definitely. lol

 

Actually, the lifted cars it would be even harder, as the engine and the disty move lower in between teh frame rails.

 

Unless you are talking about an 8in lift or something crazy.  then the engine would be fully below the frame rails.

 

just not really an upgrade to go from EA81 to EA82.

Link to comment
Share on other sites

  • 2 years later...

Hello again, 

Thanks for the advise back then. I’ve taken some time to consider my options and have decided on using the 81 GL wagon body(white), the dual range 5spd from my 86 wagon(silver), and 2.2 EJ from a 96 Legacy(silver) that I recently picked up. I’ve been doing as much reading up as time allows but still have questions!?!

1. How can I tell what the gearing is in the 81 rear diff?

2. Will I need to swap the rear diff from the 86 to match the transmission? 
 

3. If so, will I need to swap axle shafts? Front/Rear?

I will have a thousand more questions I’m sure, super excited to finally be moving forward!!!

 

3B7E9D5F-63E9-4DDF-9967-BFFC6BAB6E09.jpeg

D894C261-B24E-40FF-AEC9-AF8B63F8D79A.jpeg

Link to comment
Share on other sites

If unsure of diff ratio (there’s usually a sticker on the back of the rear diff on these older Subaru’s), swap in the rear diff from the donor car. It will bolt in no worries. 

Drive shafts - use the MY units front and rear. 

I thought you’d have more EJ conversion questions than what you didn’t have there :P 

Cheers 

Bennie

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

×
×
  • Create New...