they make brass wire wheels that work just fine. the brass is softer than the steel wire wheels. I use my 18v dewalt on highspeed and havent had any problems. Hell I took off an old head gasket before and it didnt hurt the head so I say go to town with the wire wheel
Welcome to Ultimate Subaru Message Board, my lurker friend!
 |
Welcome to Ultimate Subaru Message Board, an unparalleled Subaru community full of the greatest Subaru gurus and modders on the planet! We offer technical information and discussion about all things Subaru, the best and most popular all wheel drive vehicles ever created. We offer all this information for free to everyone, even lurkers like you! All we ask in return is that you sign up and give back some of what you get out - without our awesome registered users none of this would be possible! Plus, you get way more great stuff as a member! Lurk to lose, participate to WIN*!
* The joy of participation and being generally awesome constitutes winning ** Not an actual guarantee, but seriously, you probably won't regret it! Serving the Subaru Community since May 18th, 1998! |
Guest Message by DevFuse
EA82 waterpump replacement
Started by
Caboobaroo
, Nov 27 2004 09:06 PM
38 replies to this topic
#27
nkx
-
- Members
- 891 posts
Rallycross Junkie
- Carlisle, PA
Posted 09 September 2006 - 02:48 PM
where should i put rtv? on both sides of the new wp gasket??
#28
Caboobaroo
-
- Members
- 6,920 posts
USMB Drunk
- Oregon City
Posted 09 September 2006 - 07:48 PM
where should i put rtv? on both sides of the new wp gasket??
yup but make sure you only put a thin layer on it or else it'll seep into the coolant passages and make its way around the system. Bad juju...
#29
bec4bec
-
- Members
-
- 1 posts
Newbie
- Rathdrum, ID
Posted 09 January 2015 - 11:58 AM
Make sure to use a genuine Subaru o-ring on the water outlet to radiator( the metal pipe pushed into pump). I used the one that came with an aftermarket pump and it leaked until I put a factory one in. 
#30
Subaru_dude
-
- Members
- 1,499 posts
1000+ Super USER!
- Morristown, TN
Posted 09 January 2015 - 04:30 PM
8 1/2 years. Impressive.
#31
Subaru_dude
-
- Members
- 1,499 posts
1000+ Super USER!
- Morristown, TN
Posted 09 January 2015 - 04:31 PM
8 1/2 years. Impressive.
Oops, I mean over 10 years. Was counting from my post in 2006.
#32
Caboobaroo
-
- Members
- 6,920 posts
USMB Drunk
- Oregon City
Posted 10 January 2015 - 03:36 PM
When I saw this thread pop up, it made me laugh to go back through and read it.
#33
Crazyeights
-
- Gold Subscribers
- 1,155 posts
Crazyeights
- Pacific Northwest
Posted 10 January 2015 - 03:48 PM
When I saw this thread pop up, it made me laugh to go back through and read it.
After all these years it is still pretty relavant too. I am still working on these things at times, and they still run great!
#34
DaveT
-
- Members
- 981 posts
Subaru Nut
- Colchester
Posted 10 January 2015 - 05:36 PM
I don't think I have ever put in an Oem o ring on the water pump, and I have not had trouble. I do make sure the pump surface is good, and the steel tube groove is clean. On some, I did use a small amount of rtv to seal the ring to the groove, as it was not in rhe best shape. More recently, I have been using a little bit of plumber's silicon grease on coolant hoses and o rings. Let's the move a bit and seal up, also, the hoses are not stuck on when I have to remove them.
#35
Crazyeights
-
- Gold Subscribers
- 1,155 posts
Crazyeights
- Pacific Northwest
Posted 10 January 2015 - 06:11 PM
+1 About not needing a factory o-ring if the tube is good. I have never ordered one. I have used the factory metal gaskets though, if this is the right EA for those.
Edited by Crazyeights, 10 January 2015 - 06:11 PM.
#36
DaveT
-
- Members
- 981 posts
Subaru Nut
- Colchester
Posted 10 January 2015 - 07:08 PM
EA82 water pump uses a paper gasket.
#37
Caboobaroo
-
- Members
- 6,920 posts
USMB Drunk
- Oregon City
Posted 11 January 2015 - 04:59 PM
I found that I had to use an OEM o-ring on my XT6 as all the aftermarket versions I found were not quite as thick as the OEM one. Had two of them start leaking after 10,000 miles before I fitted the OEM o-ring.
#38
MilesFox
-
- Members
- 10,665 posts
Catch this Fox!
- Madison/Milwaukee, WI
Posted 11 January 2015 - 05:18 PM
""
Edited by MilesFox, 11 January 2015 - 05:19 PM.
#39
MilesFox
-
- Members
- 10,665 posts
Catch this Fox!
- Madison/Milwaukee, WI
Posted 11 January 2015 - 05:18 PM
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users
