Welcome to Ultimate Subaru Message Board, my lurker friend!
|Welcome to Ultimate Subaru Message Board, an unparalleled Subaru community full of the greatest Subaru gurus and modders on the planet! We offer technical information and discussion about all things Subaru, the best and most popular all wheel drive vehicles ever created.
We offer all this information for free to everyone, even lurkers like you! All we ask in return is that you sign up and give back some of what you get out - without our awesome registered users none of this would be possible! Plus, you get way more great stuff as a member! Lurk to lose, participate to WIN*!
* The joy of participation and being generally awesome constitutes winning
** Not an actual guarantee, but seriously, you probably won't regret it!
Serving the Subaru Community since May 18th, 1998!
more efi madness(she runs, and drives!)
Posted 17 December 2004 - 01:18 PM
er27 into a carbureted car. i have spark and fuel, if i try and start it with the pump hooked up, it gets too much fuel and floods. if i unplug the pump, it bleeds off the pressure with a few cranks of the engine, then runs for about 5 seconds, then dies.
when it runs it only goes up to 10 lbs of vac, and im lookin for around 20 at least. so that makes me think my fpr isnt bleeding off enough pressure, because of a giant vac leak. well, the giant vac leak is the idle air controll valve, or whatever. but it wont run without it...
anyone think that disty timing would make your car have less vac at idle than it should?
ug help =/
Posted 17 December 2004 - 03:04 PM
return line pluged?
yes timing will effect vacume. you can actually set timing by watching a vacume gauge.
Posted 17 December 2004 - 03:17 PM
i gotta mess with the timing again i suppose.
i marked the disty when i pulled it out, but i think i bumped the engine while it was out. i know im not 180 out, and thats what matters =/
thanks will report back, im so close.
Posted 17 December 2004 - 03:57 PM
one tooth off on the disty does crazy stuff.
Posted 17 December 2004 - 04:14 PM
when you get done post pics if you can. sound cool.
Posted 17 December 2004 - 05:52 PM
Can't wait to come over and ride in it.... mabye drive it? Too bad I'm stuck at work late redoing some crap becuase someone else messed up....
Been a while coming but I knew you would do it.
Posted 17 December 2004 - 06:28 PM
i just went for a more extensive test drive with no hood, its hard to not spin the tires... well tire, its open diff rear wheel drive! =] its time to drive her to texas and dyno tune the hell out of her. when i tell peepl its my dream car they look at me funny. when i open the hood they wont anymore!@#$#$@!!!!
wrx? mines bigger! celebration time
Posted 17 December 2004 - 09:02 PM
Posted 17 December 2004 - 11:24 PM
Are you using the EA81 tranny?
Posted 18 December 2004 - 06:21 AM
You're using the Stock Dash Tach? It reads the 6-cylinder RPMs correctly?
Would love to see this Hatch in person one of these days.........
On another note: They cut the Mon-Fri overtime down, and cancelled week-end OT for a while. (Darn, only 67.5 hours in this week) Maybe, I'll have time to get caught up on household chores, and have time to wrench on the '82 now. One can only hope!!!!
Posted 18 December 2004 - 09:17 AM
Posted 18 December 2004 - 11:56 AM
And to think, I was told by a mechanic that an ER27 wouldn't fit in my EA82 wagon! Way to go.
Posted 18 December 2004 - 12:05 PM
That really shows that you can do anything if you put enough effort forth. That thing must really be able to haul just barely getting on it.
Posted 18 December 2004 - 12:52 PM
ya, im heading to texas late january, where my cousin runs alamo autosports, and ennis race way is right down the road, so numbers for sure! @sap.
Place your bets!
I predict mid 15 second 1/4 mile runs at approximately 84-86mph. [On Excellent runs]
If you like burning rubber or have problems with tire slippage, I predict low-mid 16 second runs at approximately 82-84mph. There you have it.
Posted 18 December 2004 - 01:30 PM
i cant wait to see how much of the 150hp im gonna get to the ground. 100+ at the wheels would be nice =].
its a 4 wheel dyno, so i could stick my front axles in too.
Posted 18 December 2004 - 10:01 PM
Posted 18 December 2004 - 10:09 PM
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users