Jump to content
Ultimate Subaru Message Board

Search the Community

Showing results for tags 'ej22t'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Welcome to the USMB!
    • Meet n' Greet. Your USMB Welcome Center
    • Members Rides
  • Older Generations of Subaru's 1960-1994 Except Legacy and Impreza
    • Historic Subaru Forum: 50's thru 70's
    • Old Gen.: 80's GL/DL/XT/Loyales...
  • Newer Generations of Subaru discussion
    • 1990 to Present Legacy, Impreza, Outback, Forester, Baja, WRX&WrxSTI, SVX
    • BRZ and its Sister the Scion FRS/Toyota GT86
    • Crosstrek "XV"
  • Marketplace
    • Ultimate Subaru Store
    • Products for your Subaru
  • Upgrading and Racing Discussion
    • Performance Tech Forums
    • Subaru Modifications
    • Subaru MotorSports
  • Ultimate Subaru Repair Manual-The Knowledge Base of USMB. Complied posts and writeups to common problems and projects.
    • Submit a Tip or Mod to the USRM
    • Product Links and References
    • The old Ultimate Subaru Repair Manual
    • Engine
    • Engine Electrical
    • Transmission, Axle, and Brakes
    • Heating and Cooling systems
    • Body Exterior
    • Interior / Body Electrical
    • Stereo tips and tricks
    • Offroad Modifications
    • Suspension and Steering
  • Off Topic Areas
    • Shop Talk
    • Alternative Vehicles (non soob)

Product Groups

  • Member Accounts
  • Ultimate Subaru Decals
  • Subaru Parts
    • Weber Carbs and Parts
    • Used Subaru Parts

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests


Full Real Name


Occupation


Ezboard Name


Referral


Biography


Vehicles

Found 4 results

  1. Hello I need a little help. I'm working on rebuilding my EJ22t that come out of a 1992 Legacy. When I was putting on my new piston rings I noticed my compression ring was really loose. So I pulled out my calipers and measured my old rings. Turns out my oil scraper ring and my compression ring were the same thickness, so I'm assuming I need to get a set a rings that are 1.5mm 1.5mm 3mm. so I went online and all I been able to find are 1.2mm 1.5mm (3mm or 2.8mm) and the set that I all ready have is 1.2mm 1.5mm and 3mm, at this point I'm starting to feel like I'm going crazy. If you guys need pictures of anything just let me know and i will post them up. Thank you
  2. But it is. Unfortunately. I'm sorry to ask but there is no one else in this world who has tried hard enough to get this to work. Unfortunately there is no spark. So here's the project. It's a EJ22T from a 93 Legacy (Auto) going into my 86 Brat (Manual) with a dual range 5 speed transmission from a 85 GL. I did not see this engine run as it was pulled out from a wrecking yard. Compression is solid. Only 165'000 km on the engine and it looks like it was dealership maintained. Everything is hooked up "properly" as so I've been told by what I would call "Subaru gurus". These are guys who have done numerous engine swaps before. Everyone has been amazingly enthusiastic, supportive and generous with this project as I could have imagined. It is all very much appreciated. However we can't figure out why shes not sparking. There is power to the coil. Coil has been checked of ohms and swapped out with three backups, they are all good. Plugs have been checked for ohms, they're good. Cam and Crank sensors have been checked for ohms, they are good and swapped again with checked and good sensors. Five grounds in the engine are good. ECU has been swapped three times and they are all good. It is grounded. Fuel pumps hard, fast and fresh. I'v had to replace a few connections due to old/dried out cracked wires but everything looks and tests good now! We're out of ideas now which is why I ask the godly experts of this board. Any thoughts or ideas are very much appreciated. Here are a couple galleries of the swap so far! http://imgur.com/a/EjDxS http://imgur.com/a/N6NzX
  3. so I'm just trying to see if this is possible. what i'm thinking about doing to taking a 86 brat and pull the motor and trany. i've found a donor car that i would take the trany, drive line, rear diff, and cv axles out of so i would have stronger parts to hold up better. i figured i would have to get a drive line made to fit the right length. i want to put a ej20 or ej22 motor into it to give it some go. the donor car is a mid 90's legacy. i just want to try and find out what i need to do before i get to deep into this build and get stuck. anything will help out.
  4. So, I can't get a definitive answer about what i'll need for a crossmember to drop my ej22t into my xt6. I was told an ea82t crossmember would be workable and i've gotten conflicting info there stating that the xt crossmember won't bolt up to the mount holes in the 6... anyone here done the swap before?
×
×
  • Create New...