Jump to content
Ultimate Subaru Message Board

Search the Community

Showing results for tags 'bind'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Welcome to the USMB!
    • Meet n' Greet. Your USMB Welcome Center
    • Members Rides
  • Older Generations of Subaru's 1960-1994 Except Legacy and Impreza
    • Historic Subaru Forum: 50's thru 70's
    • Old Gen.: 80's GL/DL/XT/Loyales...
  • Newer Generations of Subaru discussion
    • 1990 to Present Legacy, Impreza, Outback, Forester, Baja, WRX&WrxSTI, SVX
    • BRZ and its Sister the Scion FRS/Toyota GT86
    • Crosstrek "XV"
  • Marketplace
    • Ultimate Subaru Store
    • Products for your Subaru
  • Upgrading and Racing Discussion
    • Performance Tech Forums
    • Subaru Modifications
    • Subaru MotorSports
  • Ultimate Subaru Repair Manual-The Knowledge Base of USMB. Complied posts and writeups to common problems and projects.
    • Submit a Tip or Mod to the USRM
    • Product Links and References
    • The old Ultimate Subaru Repair Manual
    • Engine
    • Engine Electrical
    • Transmission, Axle, and Brakes
    • Heating and Cooling systems
    • Body Exterior
    • Interior / Body Electrical
    • Stereo tips and tricks
    • Offroad Modifications
    • Suspension and Steering
  • Off Topic Areas
    • Shop Talk
    • Alternative Vehicles (non soob)

Product Groups

  • Member Accounts
  • Ultimate Subaru Decals
  • Subaru Parts
    • Weber Carbs and Parts
    • Used Subaru Parts

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests


Full Real Name


Occupation


Ezboard Name


Referral


Biography


Vehicles

Found 3 results

  1. The patient: 1999/2000 RX Liberty wagon (EJ251) 5spd manual. Issue: swapped in second hand gearbox (pick a part special!) only to find the vehicle now has a wobble like feeling from the front left when under acceleration, becomes worse with heavier acceleration. All other times the vehicle generally feels unsettled. Both of these issues were not present with the last gearbox. The other issue is that I have that totally awesome “catch-let go-catch-let” go feeling or experience when turning tight such as when performing a U turn - classic symptoms of a dead centre diff.Questions: 1) can a stuffed centre diff create the issue with the front end that I’m experiencing?2) can the viscous gel stuff leak from the viscous LSD housing, and if so, what does it look like? Question 2 was asked because after stripping down the old box that was replaced, I’ve found a ball of what looks like silicone near the front diff area, and in between the drive and output of the centre diff is the same sort of material. It does seem like silicone but it’s just odd. This gearbox has presumably done over 400k km now - if it hasnt been changed at some point. It was swapped because of a bearing noise and it was slipping out of gear (possibly due to shot pitch stopper rod and gearboxs mount).Upon rotating the centre diff it seems the noise is in the rear bearing. This centre diff is good so itll end up in the wagon either way - unless that grey material is the viscous gel stuff. The plan is to build one good box from the two. I’ll be replacing the front diff bearings, all seals and most likely use the centre diff bearings from the replacement box as there’s zero noise from this box, other than the noise when performing a U turn. Cheers Bennie
  2. Hi again friends. I recently had my clutch changed and immediately after, I had an issue where I would put the car in 1st or reverse, try to release the clutch and it couldn't move, making the engine bog down as if the emergency brake was on or the gears were somehow bound up. However, once I press and release the clutch, the car would take off as usual. Now it continues to bind up occasionally like that (maybe once per day) but an extra press and release of the clutch frees things up. It feels like maybe 4wd becomes partially engaged (just enough to bind - if that's even possible); however I don't understand why it would start immediately after the clutch was changed and why a press of the clutch would release it. Does anyone know what the problem is? Thanks in advance. JW 86 gl 1.8 5sp dual range 4wd
  3. I have 2006 Outback Limited, when making tight slow turns I can feel the torque bind. If I back out of my driveway with the wheel turned and then shift into drive it hits in hard. When the car is in park and I turn off the ignition it will slightly lurch forward. I have measured all the tires and all are the same, although I did drive the car on a low tire for about 40 miles the day I bought it. it was at about 20PSI I have checked the voltage to the transfer clutch duty solonoid 1.5 to 1.8 Volts with the solonoid connected, key on, 1st gear, not running. I have checked the voltage at the solonoid with the AWD Fuse in, 0 volts at the solonoid. The car still binds with the AWD use IN. I have checked the trans temp sensor, 4000 ohm at 70 degrees F. I have checked the throttle position sensor , (OK) I have changed the fluid twice. one flush and one filter and drop with subaru ATF. I think the transfer duty solenoid is under the trans pan on this unit and not in the tailshaft area. Please confirm. Not sure where to go from here, anything else I could check? Any help would be appreciated. Thanks Chris
×
×
  • Create New...