Jump to content
pontoontodd

long travel Outbacks or making Subarus faster and more reliable offroad

Recommended Posts

R and I each drove our cars to Jean, NV Sunday night. Filled up at the largest Chevron station in the world - 96 pumps and 60 bathroom stalls.

IMG_5228s.jpg

We met B and Z at the check in counter in the Terrible casino.

Monday morning I got up early as usual to check over the suspension on my Outback and met T in the parking lot. He had driven his Outback XT 5MT there from San Diego to join us in some trail riding in NV.

IMG_5246s.jpg

T is crazy about weight reduction on his car, says it's down to 3000#.  For instance, the rear doors are gutted and the glass has been replaced with carbon fiber that's fixed in place.

IMG_5247s.jpg

The five of us had breakfast and checked out the off road hall of fame.

IMG_5233s.jpg

IMG_5234s.jpg

IMG_5235s.jpg

IMG_5236s.jpg

IMG_5241s.jpg

IMG_5242s.jpg

One interesting combination was a Jeep and a Rokon that had driven the Darien gap (first two wheeled vehicle to do so).

IMG_5238s.jpg

IMG_5239s.jpg

Edited by pontoontodd

Share this post


Link to post
Share on other sites

We met with J and he took us to some whoops outside of town that were a little too big to run fast over with the Subarus. He was fairly impressed with what they could do and took us to some smaller ones along a dirt/gravel road. They were similar to the super whoops in the UP but narrow and on top of a crowned trail so we couldn't comfortably go much over 30mph. Unfortunately there was a ditch I didn't see until the last second and didn't slow down enough to prevent from plowing into the opposite side of it. It cracked one of the coolant fittings for the oil cooler.

IMG_2067s.jpg

B and Z went into town to get some fittings and we took off the skidplate and cleaned things up and talked with J.  After we got it back together we ran the cars over the whoops again (including T's for reference). J recommended valving changes at both ends. He had a small bottle that was good for charging maybe eight shocks but wasn't fully pressurized. I asked him if he had a vice and he asked if we had a receiver. I told him we have 1.25” receivers and he says with a look of disgust “that's not a receiver.” We were able to C clamp it to the rear bumper of the Outback. He also had a little toolkit that had an allen wrench and spanner wrench we needed. He left to pick up some steel as we figured it would take about four hours to go through all the shocks in the desert. 

IMG_2071s.jpg

IMG_2075s.jpg

IMG_2079s.jpg

IMG_20190930_151222s.jpg

It didn't feel a lot better in the car, mainly we noticed the car stayed almost perfectly level but bounced up and down. It definitely looked better from outside on video.  He also took us to a deeply whooped out recent racecourse leading to some embedded rocks, B and I both thought the Outback rode better over them than with the old shock tuning in Texas. J had mentioned earlier in the day he'd never owned a car, only pickup trucks, but was looking up Subarus on Craigslist by the end of the day.

IMG_20190930_110512s.jpg

IMG_20190930_111154s.jpg

IMG_5264s.jpg

Edited by pontoontodd

Share this post


Link to post
Share on other sites

We asked J for a good place to camp north of town and he recommended some sand dunes just off 95 so we drove up there and camped overnight.  Those are the dunes just to the right of the sign beyond the power lines.

IMG_20191003_090220s.jpg

IMG_5265s.jpg

IMG_5268s.jpg

20191001_065538s.jpg

IMG_2094s.jpg

Tuesday morning we ate breakfast, packed up, and drove the last few miles to the big dune.

IMG_5270s.jpg

It was certainly described accurately, the center dune was hundreds of feet high with no tire tracks going to the top of it. I was driving over one dune when we suddenly got to a sharp drop off the other side so I turned to avoid it and got stuck shortly afterwards because I was going too slow.

IMG_2101s.jpg

We aired down the tires and got it out with the sand ramps and pushing. Aired down the other cars, and took turns driving each others' cars around the dunes.  T's suspension was bottoming out easily so we unpacked his cargo while we drove around the dunes.  I found one good little jump, the last time I hit it the driver's side got up much higher than the passenger side. Since it was soft sand the landing was fine.

IMG_5272s.jpg

IMG_20191001_082850s.jpg

IMG_5278s.jpg

Share this post


Link to post
Share on other sites

Eventually we decided to see other parts of Nevada, repacked T's car and aired back up. He rode with me in my Outback down the ~5 mile whooped out road/trail to the main gravel road. We were going 50mph and he was amazed the whole time by what the car could do. There were a few spots where we'd get air going into a sweeping turn, it was a fun stretch. Our next stops were a few spots along the 2016 and 2017 V2R courses that we'd wanted to revisit. The first one was a highway underpass the course went through in 2017. Took about a five mile trail to get there eventually driving in a wash. A concrete tunnel goes under the highway that's only about 8 feet tall. There were various scrape marks down the roof of it from trucks and buggies that barely fit.

IMG_20191001_125442s.jpg

On the opposite side of the highway is a giant pile of 2' rocks the highway department piled up to reduce erosion.

IMG_5282s.jpg

We did not drive through it but decided if it was part of the course again we'd just have to take it slow and hope for the best.

IMG_20191001_130622s.jpg

IMG_20191001_133538s.jpg

Then we drove up the highway to some other trails leading to a cattle guard jump along a gravel road we'd hit at about 80mph during the 2017 race. We were going slightly downhill, the opposite direction we'd raced in, and figured we could just try it at increasing speeds so the first time I hit it at 65 and we got some air, seemed like we could hit it faster. T pulls up and says he hit it at 80. We didn't believe him at first. Hit it both ways a few times, seemed like 80 uphill and 90 downhill was about all my Outback could do. Landed fine. Apparently T hit it uphill once and had a bouncy squirrelly landing so he parked his car.

IMG_20191001_135648s.jpg

IMG_20191001_140318s.jpg

IMG_20191001_140344s.jpg

We continued up the former race course, part of which was surprisingly overgrown. We cut over to the 2016 course to go over a mountain and hit a different jump. 

IMG_5298s.jpg

IMG_5304s.jpg

IMG_5309s.jpg

IMG_5310s.jpg

IMG_5311s.jpg

On the way to the downhill jump we were circling a dry lake bed so we decided to drive down to that.

IMG_5312s.jpg

We got some pictures and videos of the cars driving around on the lake bed. The surface was sticky, I couldn't get my car to slide around at all and didn't want to roll it. One end had many bushes about a hundred feet apart, it was fun to drive through them at speed. The lake bed was almost three miles across the long way. At one point Z was riding with me and we both felt disoriented with tan in every direction for a mile or so and I slowed down. 

IMG_5315s.jpg

IMG_20191001_163016s.jpg

IMG_5317s.jpg

IMG_20191001_163553s.jpg

IMG_2156s.jpg

IMG_20191001_164259s.jpg

We drove the long grade up the mountain and had some of the shifting back and forth between third and fourth we'd experienced in 2016. Except then we had the four cylinder and I think it was second and third.

IMG_5321s.jpg

20191001_170030s.jpg

IMG_20191001_170100s.jpg

IMG_5323s.jpg

At the top the tailing pile had shifted the road over to the side. I think it was downhill from that we drove the narrow switchback trail through the pine forest. B still wonders how the trophy trucks get through that section – it has a bunch of tight, narrow U turns. We hit the downhill jump at 70mph which just felt like the car was getting light but the cameramen did say we were leaving the ground. I didn't feel comfortable going over 70mph on that road so we continued up to Tonopah. T parked his car and B and I tried to drive a switchback up a small mountain/large hill but it turned out to be a bit of a maze so we came back down. We did get a good view of town and some wild horses though.

IMG_5335s.jpg

IMG_2159s2.jpg

IMG_5346s.jpg

20191001_180126s.jpg

Looks like the road leading down from that saddle into town has a bunch of jumps along it but we went back down to where T was parked. We continued on the race course that follows some white hard ground that tasted salty, appeared to be a few foot deep salt deposit that went on for miles. We continued to some concrete barriers in the wash at a break in an old railroad grade where there were a lot of spectators. We couldn't figure out at first how the trophy trucks make it through there, the gap between the barriers is maybe 7' wide, but then we decided they must just drive over one side (these concrete piers are about 2' high). There was an old oil pan embedded in the wash, we decided someone probably thought they were going to clear one of the concrete barriers and then it ripped their oil pan off.

IMG_5355s.jpg

IMG_20191001_182617s.jpg

We took a short trail to the highway and drove into Tonopah for gas and to cook some food. Talked to T, he decided to stay the night in Tonopah and decide his fate in the morning. We warned him that the last forty miles of the V2R course we wanted to run the next day would be too rough for his car. We drove to a city park and cooked dogs. Then we headed farther up 95 and camped at Walker lake.  On the way down the road to the campground there were signs for the former lake levels in increasingly recent years. Z said he read that as the river has been diverted for agriculture the lake has been draining. It was quite salty.

Share this post


Link to post
Share on other sites

Wednesday morning we ate breakfast and packed up.

IMG_5370s.jpg

20191002_064808s.jpg

IMG_5371s.jpg

20191002_075901s.jpg

IMG_20191002_080443s.jpg

IMG_5379s.jpg

IMG_5383s.jpg

IMG_20191002_081141s.jpg

While we were packing up and telling stories, B pointed out a switchback trail up a mountain across the highway and we of course all thought it was a great idea to try to drive the Subarus up it. It was fairly steep and rocky but we made it up about 2/3 of the way pretty quickly.

IMG_5388s.jpg

IMG_5393s.jpg

Eventually I got to a point where I ran out of power/gearing and slowly backed down to the previous switchback/intersection and waited. B and R got quite a bit higher, they think near the top, and the trail eventually got too loose and steep so he had to come back down.

IMG_20191002_091304s.jpg

He had trouble getting it back in high range so we decided he should not use low range the rest of the trip unless absolutely necessary.

IMG_5395s.jpg

20191002_093003s.jpg

IMG_20191002_094204s.jpg

Share this post


Link to post
Share on other sites

We drove up the highway to the closest PRC (public road crossing) to the end of the V2R course, 42 miles from the end. As soon as we got on the highway I felt like the car was leaning to the right a bit but quickly forgot about it. Not too far in to the race course, B's car was running hot in the soft washes so we stopped to let it cool off. While we were stopped, Z suggested looking for the source of the noise coming from the back of the Outback. There was a 1-2” gap in the crack in the RR strut tower that I'd welded up before the trip. Weld itself seemed to hold, there's just not much structure left there.

IMG_5402s.jpg

We got out the heavy duty safety wire and a couple ratchet straps, jacked up the car and pulled the strut tower back down to about where it was. We found a rock to jam in the frame and hose clamped that in place.

IMG_20191002_131323s.jpg

We got going again and went by a smaller lake bed that had a burned out first generation Mazda RX7 next to it. We spent some time examining that.

IMG_5407s.jpg

IMG_20191002_143135s.jpg

 

IMG_5414s.jpg

It's amazing to me how hot a car fire can get, the transmission case was even melted on this one and the springs were fully compressed from losing their temper.

IMG_5418s.jpg

IMG_5420s.jpg

We then got to a rocky wash that's part of the course but were able to drive through it without any problems. We drove up a long rocky grade, maybe five miles uphill through 6-8” rocks. Not extremely steep but had to keep moving due to the lack of low range. Made it through that alright and there was nothing too rough beyond that. Unfortunately we did not get pictures or videos of these rough sections.

20191002_145740s.jpg

IMG_5424s.jpg

IMG_20191002_160956s.jpg

When we started coming down the far side of the mountain there was some new equipment parked along the road that had been smoothing it out. Perhaps they will smooth out the entire road.

IMG_20191002_164113s.jpg

IMG_5451s.jpg

20191002_172609s.jpg

IMG_5452s.jpg

IMG_5454s.jpg

Near the end of the course we came up to what at first looked like a fairly tall, steep hillclimb. We were able to get a run at it in second and downshift to first most of the way up and made it to the top more easily than expected. Made it to Dayton, got fuel and burgers, and drove back south. Got to Tonopah about 10PM and decided to stay there for the night. I thought we'd really be missing a great opportunity if we didn't stay at the “world famous” Clown Motel so we did that. The rooms aren't anything special but the price was decent, beds were alright, and the shower was higher pressure than I'm used to.

IMG_5466s.jpg

IMG_5474s.jpg

IMG_20191003_070700s.jpg

IMG_20191003_070720s.jpg

IMG_20191003_071130s.jpg

In one room was a large painting of Jason from Friday the 13th.

IMG_20191003_070431s.jpg

Edited by pontoontodd

Share this post


Link to post
Share on other sites

Thursday morning we drove the rest of the way back to Vegas and dropped R off at his WRX and he drove home.  While we were in town we figured we should fix the Outback strut tower better. 

IMG_2430s.jpg

IMG_2436s.jpg

We bought an angle grinder, assortment of wheels, extension cord, and a decent ratchet strap from Harbor Freight and rented a welder and bought some steel strap and tubing from Home Depot.  We drove around town for about an hour through a big city park, checking out some RV campgrounds, following Google's directions onto an army base, and looking behind the Home Depot and Harbor Freight for outlets with no luck. 

DSC00111s.jpg

So we proceeded with plan G – renting a generator from Home Depot. Their largest model is 6800 watts and is wheelbarrow style with handles and wheels. Guy asked if we needed help loading it in our vehicle and we just told him no. 

IMG_2439s.jpg

IMG_2492s2.jpg

I used the piece of welding glass we keep in the car. I'm shocked they rent welders to the public without even suggesting they buy or rent a welding helmet.

IMG_2443s.jpg

IMG_2444s.jpg

IMG_2452s.jpg

IMG_2457s.jpg

IMG_2462s.jpg

Fabrication went relatively smoothly, welds turned out OK for flux core. 

IMG_2469s.jpg

IMG_2470s.jpg

IMG_2471s.jpg

IMG_2472s.jpg

Ran two strips from the strut mount plate down to some solidish sheet metal.

IMG_2488s.jpg

Added a couple tubes from just above the strut mount to the bottom of the main roll hoop and the top of the trailing arm mount.  It's no spare tire inflated against the roof but it held the rest of the week.

IMG_2489s.jpg

20191003_150552s.jpg

We've been talking about a portable welder all year and now we're convinced we need to come up with something. A flux core spool gun wouldn't take up much space or weigh much. Two batteries or a modified alternator would probably work as a power source. Packed everything back up, got dinner at a Mexican restaurant near there, and headed out of town. Hit a random trail/dirt road in AZ along 15 that had a few little jumps on it.

IMG_5500s.jpg

IMG_5501s.jpg

IMG_5522s.jpg

IMG_5523s.jpg

Got to Sand Hollow State Park near St. George, UT after dark and paid the primitive camping fee and found a spot along the edge of the lake with a picnic table. Lake has swimmer's itch (caused by the snails that live there). It was crawling with golf carts, Jeeps, etc. Had a small praying mantis on my tent while I was setting it up.

IMG_5541s.jpg

  • Like 1

Share this post


Link to post
Share on other sites

Friday morning we tried going up a few trails that we could see from the campsite but they were ultimately gated off.

IMG_5555s.jpg

IMG_5567s.jpg

IMG_2506s.jpg

IMG_5589s.jpg

IMG_5598s.jpg

Found the tunnel/underpass to get to the main dune/rock area. There's a large hill you can drive up either on fairly extreme rock crawling trails or a long soft sandy grade.

IMG_5606s.jpg

IMG_5607s.jpg

IMG_5609s.jpg

IMG_5613s.jpg

IMG_5616s.jpg

We weren't able to get all the way to the top in the sand so we decided to go elsewhere.

IMG_5617s.jpg

IMG_5620s.jpg

IMG_5622s.jpg

The next trail we went to was Massey SW #15 Skutumpah Road. We had to drive through Zion National park, scenery was amazing but we had to wait a couple times for a half hour due to traffic/construction. We did see mountain goats sitting about 20' off the road I think going through Zion.

IMG_5629s.jpg

IMG_5633s.jpg

When we got to the start of the road there was a sign indicating it was closed 15 miles ahead (it's a 33 mile long road).

IMG_5635s.jpg

We decided to drive up it and see if it was actually closed (it was, but I think more than 15 miles in) and then took some side roads/trails instead. These followed some soft sandy/gravelly washes through some small canyons until we got to 95. 

IMG_5643s.jpg

IMG_5644s.jpg

IMG_5650s.jpg

IMG_5653s.jpg

IMG_5656s.jpg

IMG_5659s.jpg

IMG_5666s.jpg

Many soft sandy sections and portions that were cut/milled into solid rock. Those road beds probably don't require much maintenance. After we drove east on 95 we drove Massey SW #20 Nipple Creek / Tibbet canyon which was my favorite on this trip. It was a good Subaru difficulty level – the average lifted Forester/Outback could probably have done it but I don't think my stock Impreza could have. Fun sections in canyon washes and some awesome views.

IMG_2555s.jpg

IMG_5680s.jpg

I think it was on this trail we observed that we'd driven for a few hours with no signs of current or former human habitation aside from the road we were driving on. Then we drove up SW #21 Smoky Hollow trail. We camped out on a big flat tailings pile from an old coal mine.

20191004_191814s.jpg

We made a campfire and burned oily rags, cardboard, wood, a cow pie, and coal all at the same time.

IMG_5696s.jpg

Share this post


Link to post
Share on other sites

IMG_5705s.jpg

IMG_5706s.jpg

IMG_5709s.jpg

IMG_5711s.jpg

IMG_5713s.jpg

Saturday morning we headed north up SW #18 Smoky Mountain road, it was a wide and fairly smooth dirt road. We actually saw people camping and on an ATV.

IMG_5716s.jpg

IMG_5717s.jpg

IMG_5721s.jpg

IMG_5723s.jpg

There were a few decent jumps on this road, one was a cattle guard just before a fairly hard right hand turn. We got some video of the cars hitting that. There was another big uphill tabletop that we decided would have to wait for another trip. By the time we got to the town of Escalante it was time to drive straight home on pavement. Just north of the town of Escalante there was a narrow ridge road with no guardrails with amazing views. Driving through Escalante we saw probably the best overlooks of the trip, it's over 10k feet and you can see a huge amount of red rock formations down at 5k feet, like looking out of a plane. We drove through Escalante and Capitol Reef national parks but didn't have time to really check them out. We passed Swingarm City stunt area and avoided the temptation to spend time there. We camped at a big sandy lake in Nebraska.

Sunday morning we packed up and continued driving back.  I had noticed a slight vibration but thought maybe it was just the concrete. Somewhere in Iowa I heard a pop and the vibration increased. Pulled over and didn't see any obvious problems or leaks so we got off at the next exit and drove to a parking lot. The front u-joint was sloppy, somehow one of the cups had come out. Put in a new one and snapring and continued.  We all got home without any more problems.

Share this post


Link to post
Share on other sites

Overall it was a good trip. We made progress tuning the shocks and got some ideas for how to improve them further. End of the V2R course didn't seem too bad so we're planning on trying that again next year. Frame fix was one of our best yet. Have to improve some things over the winter. No CV axle replacements so the softer springs on the Forester probably helped with that. I put just over 5000 miles on my car. Got 18-20mpg on the highway, considerably better than the 17mpg I am used to with the EZ30. Wondering if the fuel pump or an injector is going bad. Optimistically it could be due to improved flow through the new (to the car) cats. Only used two quarts of engine oil, B said the Forester's oil consumption was less than that.

The three big things I decided we should do to my black Outback before the V2R are:

rear strut tower reconstruction and addition of tubes to rollcage

front skidplate lowering/adding engine clearance – already started on this

safety wiring and/or cotter pinning all suspension fasteners and exhaust manifold nuts

There are many other modifications, inspections, and preventative maintenances that are on the list too.  I've been thinking about it for a while but T made us think about weight reduction more, we think we can take 100# or more out of the car fairly easily while lowering the center of gravity.

Edited by pontoontodd

Share this post


Link to post
Share on other sites
8 minutes ago, pontoontodd said:

Overall it was a good trip. We made progress tuning the shocks and got some ideas for how to improve them further. End of the V2R course didn't seem too bad so we're planning on trying that again next year. Frame fix was one of our best yet. Have to improve some things over the winter. No CV axle replacements so the softer springs on the Forester probably helped with that. I put just over 5000 miles on my car. Got 18-20mpg on the highway, considerably better than the 17mpg I am used to with the EZ30. Wondering if the fuel pump or an injector is going bad. Optimistically it could be due to improved flow through the new (to the car) cats. Only used two quarts of engine oil, B said the Forester's oil consumption was less than that.

The three big things I decided we should do to my black Outback before the V2R are:

rear strut tower reconstruction and addition of tubes to rollcage

front skidplate lowering/adding engine clearance – already started on this

safety wiring and/or cotter pinning all suspension fasteners and exhaust manifold nuts

There are many other modifications, inspections, and preventative maintenances that are on the list too.  I've been thinking about it for a while but Terry made us think about weight reduction more, we think we can take 100# or more out of the car fairly easily while lowering the center of gravity.

I've been wondering what your loaded trail weight is? I've had the thought after I look at yer pictures and videos of the speeds you hit stuff too think "Damn I'd be bottoming out my rear suspension constantly" 

That is until just recently with the addition of a second set of springs for the rear....but I digress.  

So yeah, What's that beast weigh ready to roll with a full tank?

Share this post


Link to post
Share on other sites
1 minute ago, FerGloyale said:

I've been wondering what your loaded trail weight is? I've had the thought after I look at yer pictures and videos of the speeds you hit stuff too think "Damn I'd be bottoming out my rear suspension constantly" 

That is until just recently with the addition of a second set of springs for the rear....but I digress.  

So yeah, What's that beast weigh ready to roll with a full tank?

That's a good question and one we want to answer over the winter.  I'm guessing with the cage, jacks, and fuel cell it's almost 4000#.  On a trip like that we have a good 500# of cargo in it, figure 300-400# for driver and passenger, so 4500# ++ loaded.  During a desert race it's closer to 200# of cargo (tools, spares, etc).

The main reason we're not bottoming out is the long travel struts with spring rates and damping for hard driving.  This car bottomed out all the time on the stock struts and springs when driven hard without the cage, jacks, fuel cell, H6, etc.

Share this post


Link to post
Share on other sites

Made more clearance between skidplate and engine.  Pulled down/straightened out radiator support by welding these big tubes to the skidplate again.  This time I welded the "hooks" to the radiator support so they wouldn't slip off.  I think I had it a little beyond straight under load but that was about the best I could do.  It sprung back to slightly bent but was definitely pulled down from where I started.

IMG_5802s.jpg

I was trying to figure out how to reinforce things and B suggested welding another piece of tubing to the bottom of the radiator support.  Since it's at the back edge it doesn't really hurt approach angle or get in the way.  Could have actually fit a 1" x 2" tube vertically but would have had to mostly cut out the gussets on the skidplate so I thought 1" square was a good compromise.

IMG_5835s.jpg

Fully welded with new tabs for skidplate and longitudinal tubes to the swaybar mounts.

IMG_5900s.jpg

IMG_5895s.jpg

Have already replaced three of the six skidplate side tabs with 2" wide (they all started 1" wide).  Gusseted the remaining original tabs.  Cut more clearance for the engine and rewelded a couple seams that opened up.  Trying to make it Nevada proof.

IMG_5920s.jpg

Repainted top and sides.  Didn't bother with the bottom, that stays paint and rust free from use.

IMG_7797s.jpg

Lateral tubes were pretty beat, this picture doesn't show how bad they were, but bent/smashed at the bolt holes.

IMG_5919s.jpg

I welded in tubes on the new ones and ground the welds flush.

IMG_5918s.jpg

Painted and reassembled.

IMG_7800s.jpg

 

IMG_7802s.jpg

Got the side skidplates back on too, no big changes there, welded a couple washers on some wallered out holes and hit them with a little paint.  They were a pain to install mainly due to the radiator support being pulled down.  Will see if those settle in a little with use, fortunately they don't have to come off often.

 

Will probably work on our shock tuning area this weekend before the ground freezes.  Anxious to improve the shock tuning further.  Also sounds like I'll be building a few new sets of struts over the winter.

 

Edited by pontoontodd

Share this post


Link to post
Share on other sites

Thanks for sharing! I've lurked here for a long while ever since my buddy (who races BITD Jeepspeed class) told me about your run in V2R a few years ago. You really surprised a lot of the racers!  The ruts those trophy truck leave behind are insane. I've crewed for him in the past and am going to codrive in the upcoming season. Hopefully I see you there!

Would you mind sharing a list of spares you bring along and how/where you store them while trail running? It's impressive to see you whip out a u-joint, control arm bushing, or whatever and fix your rig on the side of the trail.

 

Share this post


Link to post
Share on other sites
4 hours ago, 2002maniac said:

Thanks for sharing! I've lurked here for a long while ever since my buddy (who races BITD Jeepspeed class) told me about your run in V2R a few years ago. You really surprised a lot of the racers!  The ruts those trophy truck leave behind are insane. I've crewed for him in the past and am going to codrive in the upcoming season. Hopefully I see you there!

Would you mind sharing a list of spares you bring along and how/where you store them while trail running? It's impressive to see you whip out a u-joint, control arm bushing, or whatever and fix your rig on the side of the trail.

 

Definitely say hi at next year's V2R.  As you know there's always plenty of waiting around at off road races.

I've been thinking about typing this up for a while.  Here is what I usually take in the Subaru.

Tools that stay in the car:

3/8” and 1/2” ratchet, breaker bar, and extensions
8, 10, 11, 12, 13, 14, 17 & 19mm sockets
spindle nut socket (32mm?)
8, 10, 11, 12, 13, 14, 17 & 19mm wrenches
5/16 and 10mm nut drivers
screwdrivers
crescent wrench
vice grips
screwdriver
3' long prybar
shovel
multimeter
telescoping bottle jack
RV scissor jack
stick electrodes & welding glass
tire pressure gauge
inner CV rollpin punch
hacksaw blades
3# hammer

When trail riding I also pack an inner tie rod tool (long socket).

Spare parts that stay in the car:

belts
CV axle – 1 front, 1 rear
electrical wire
fuel pump
u joints
zip ties
tire plugs
full size spare
fasteners
fuses
hose clamps up to 8” dia
thin and thick safety wire
1/4” wheel spacers

Spare parts I pack for trail riding:

tie rod – inner and outer
lower ball joint
control arms (depending on how many stock suspension cars are going)
struts (depending on how many stock suspension cars are going)
starter
alternator
rear lateral links and trailing arm
front and rear bolt on wheel bearing and hubs

I also keep in the car:

lithium jump pack
2” snatch strap
ratchet straps
fluids (oil, brake, PS, shock)
fix a flat
recovery ramps
water jugs
wet wipes
JB weld
RTV

For trips I add:

maps
car title (if car is fairly disposable like my Impreza)
cordless recip saw with long wood blades
spare keys
12V compressor
vidcams
handheld family band radios
winch, extension cord, block & tackle

food/drinks/utensils
TP/PTs/hand cleaner
tents/sleeping bags/air mattresses
insect repellent
clothes, towel, shoes
toiletries, glasses, headlamp
phone & charger
camp stove, propane, pan, lighter

 

 

For desert racing we also pack:

rear lights
door bars & window nets
number plates
rear bumper
corner windows
harnesses
second spare tire

suits
helmets
HANS
shoes
gloves
hoods

but we usually don't take the winch and a few other things when just desert racing.

 

Unrelated, we do have some useable whoops now just outside of town.  We can hit them at about 20-30mph and they're fairly harsh so it should be a good place to tune our shocks.

  

Share this post


Link to post
Share on other sites
On 11/14/2019 at 5:00 PM, pontoontodd said:

Definitely say hi at next year's V2R.  As you know there's always plenty of waiting around at off road races.

I've been thinking about typing this up for a while.  Here is what I usually take in the Subaru.

Tools that stay in the car:

3/8” and 1/2” ratchet, breaker bar, and extensions
8, 10, 11, 12, 13, 14, 17 & 19mm sockets
spindle nut socket (32mm?)
8, 10, 11, 12, 13, 14, 17 & 19mm wrenches
5/16 and 10mm nut drivers
screwdrivers
crescent wrench
vice grips
screwdriver
3' long prybar
shovel
multimeter
telescoping bottle jack
RV scissor jack
stick electrodes & welding glass
tire pressure gauge
inner CV rollpin punch
hacksaw blades
3# hammer

When trail riding I also pack an inner tie rod tool (long socket).

Spare parts that stay in the car:

belts
CV axle – 1 front, 1 rear
electrical wire
fuel pump
u joints
zip ties
tire plugs
full size spare
fasteners
fuses
hose clamps up to 8” dia
thin and thick safety wire
1/4” wheel spacers

Spare parts I pack for trail riding:

tie rod – inner and outer
lower ball joint
control arms (depending on how many stock suspension cars are going)
struts (depending on how many stock suspension cars are going)
starter
alternator
rear lateral links and trailing arm
front and rear bolt on wheel bearing and hubs

I also keep in the car:

lithium jump pack
2” snatch strap
ratchet straps
fluids (oil, brake, PS, shock)
fix a flat
recovery ramps
water jugs
wet wipes
JB weld
RTV

For trips I add:

maps
car title (if car is fairly disposable like my Impreza)
cordless recip saw with long wood blades
spare keys
12V compressor
vidcams
handheld family band radios
winch, extension cord, block & tackle

food/drinks/utensils
TP/PTs/hand cleaner
tents/sleeping bags/air mattresses
insect repellent
clothes, towel, shoes
toiletries, glasses, headlamp
phone & charger
camp stove, propane, pan, lighter

 

 

For desert racing we also pack:

rear lights
door bars & window nets
number plates
rear bumper
corner windows
harnesses
second spare tire

suits
helmets
HANS
shoes
gloves
hoods

but we usually don't take the winch and a few other things when just desert racing.

 

Unrelated, we do have some useable whoops now just outside of town.  We can hit them at about 20-30mph and they're fairly harsh so it should be a good place to tune our shocks.

  

add a 22mm socket and wrench for suspension parts.

21 wrench for a few weird item...can't remeber.....maybe a PSpump line?

 

Share this post


Link to post
Share on other sites
On 10/14/2019 at 1:16 AM, pontoontodd said:

We met with J and he took us to some whoops outside of town that were a little too big to run fast over with the Subarus. He was fairly impressed with what they could do and took us to some smaller ones along a dirt/gravel road. They were similar to the super whoops in the UP but narrow and on top of a crowned trail so we couldn't comfortably go much over 30mph. Unfortunately there was a ditch I didn't see until the last second and didn't slow down enough to prevent from plowing into the opposite side of it. It cracked one of the coolant fittings for the oil cooler.

 

B and Z went into town to get some fittings and we took off the skidplate and cleaned things up and talked with J.  After we got it back together we ran the cars over the whoops again (including T's for reference). J recommended valving changes at both ends. He had a small bottle that was good for charging maybe eight shocks but wasn't fully pressurized. I asked him if he had a vice and he asked if we had a receiver. I told him we have 1.25” receivers and he says with a look of disgust “that's not a receiver.” We were able to C clamp it to the rear bumper of the Outback. He also had a little toolkit that had an allen wrench and spanner wrench we needed. He left to pick up some steel as we figured it would take about four hours to go through all the shocks in the desert. 

 

 

 

 

It didn't feel a lot better in the car, mainly we noticed the car stayed almost perfectly level but bounced up and down. It definitely looked better from outside on video.  He also took us to a deeply whooped out recent racecourse leading to some embedded rocks, B and I both thought the Outback rode better over them than with the old shock tuning in Texas. J had mentioned earlier in the day he'd never owned a car, only pickup trucks, but was looking up Subarus on Craigslist by the end of the day.

 

IMG_20190930_111154s.jpg

IMG_5264s.jpg

ohh wow that outback XT looks cool. interesting front skid plate or skid box this should be called. why so low hanging ? not much lift too looks like. would it be possible to know something more about that car maybe. ? im just looking for some ideas for mine. 

Share this post


Link to post
Share on other sites
On 11/17/2019 at 2:24 PM, FerGloyale said:

add a 22mm socket and wrench for suspension parts.

21 wrench for a few weird item...can't remeber.....maybe a PSpump line?

 

I do have a crescent wrench on the list.  Seriously though, I have that socket.  That list doesn't include all the little things, I typed it up off memory.

23 hours ago, scalman said:

ohh wow that outback XT looks cool. interesting front skid plate or skid box this should be called. why so low hanging ? not much lift too looks like. would it be possible to know something more about that car maybe. ? im just looking for some ideas for mine. 

Yes, the Outback XT definitely looks cool.  I tried to get T to post about it but he's 78 years old so it might be beyond his technological capabilities.  He has done a lot of work to it to reduce weight, stripping out a lot of interior, gutting the doors, replacing a lot of things with carbon fiber.  He has entered it in the Sonora rally a few times, it is a Dakar style race/navigation challenge in the dunes of northern Mexico.  The organizers of that race made him put in a cage before he entered it the last time.  I do not think I got any photos but it is a heavy duty rally style full cage.  The engine is mildly modified but I couldn't tell you exactly how.  It has a five speed manual.  With the horsepower and the light weight it did well in the dunes.  Unfortunately he'd recently had someone do suspension work to it and they made the rear suspension far too soft, even unloaded it bottomed out easily.  He will probably have us build him better suspension and join us on some of our trips next year.

Share this post


Link to post
Share on other sites
On 11/7/2019 at 6:04 PM, pontoontodd said:

Will probably work on our shock tuning area this weekend before the ground freezes.  Anxious to improve the shock tuning further.  Also sounds like I'll be building a few new sets of struts over the winter.

Get it done pontoonJ!

I promise to finally sort out my fuel issue with a non-aftermarket pump and maybe do my timing/water etc. and all the other lift and bash related stuff, too! So much to do.

Saw these folks on launch control, a Subaru powered buggy 2nd in class V2R. Way ahead in its class until a different sort of fuel issue arose (vapor lock). I've been driving around without utilizing boost for months, which is pure torture.

K

image.thumb.png.0b045f583a34b65e8556b50d0776b42b.png

Share this post


Link to post
Share on other sites

looks like your outback body is just broke man , same thing as you told me many times, just find no rust body or diff body at all you need more like baja car not subaru for your drive. 

Share this post


Link to post
Share on other sites
On 11/20/2019 at 6:51 PM, travelvw said:

Get it done pontoonJ!

I promise to finally sort out my fuel issue with a non-aftermarket pump and maybe do my timing/water etc. and all the other lift and bash related stuff, too! So much to do.

Saw these folks on launch control, a Subaru powered buggy 2nd in class V2R. Way ahead in its class until a different sort of fuel issue arose (vapor lock). I've been driving around without utilizing boost for months, which is pure torture.

K

image.thumb.png.0b045f583a34b65e8556b50d0776b42b.png

That thing is cool but it's more VW than Subaru IMO.

Share this post


Link to post
Share on other sites
On 11/23/2019 at 12:53 PM, scalman said:

looks like your outback body is just broke man , same thing as you told me many times, just find no rust body or diff body at all you need more like baja car not subaru for your drive. 

Do you know this guy?

https://www.youtube.com/watch?v=u1LKD7s6k3I

 

More on the body repair soon.  Again, if it didn't have a cage, fuel cell, etc in it I would have replaced it by now.

Share this post


Link to post
Share on other sites
10 hours ago, pontoontodd said:

Do you know this guy?

https://www.youtube.com/watch?v=u1LKD7s6k3I

 

More on the body repair soon.  Again, if it didn't have a cage, fuel cell, etc in it I would have replaced it by now.

Yes its one of our famous rally drivers, he was on dakar now 3 or 4 years with 2 others from our country. 

 

Can you just remove everything cage fuel cell other stuff and put into good no rust body. Still i think long travel suspension is not for poor subaru bodys, or you need to add lots metal on it to make it stronger.

Edited by scalman

Share this post


Link to post
Share on other sites
57 minutes ago, scalman said:

Yes its one of our famous rally drivers, he was on dakar now 3 or 4 years with 2 others from our country. 

 

Can you just remove everything cage fuel cell other stuff and put into good no rust body. Still i think long travel suspension is not for poor subaru bodys, or you need to add lots metal on it to make it stronger.

It would be very difficult to swap the cage into a different body, at least if you want to keep the windows and doors functional, which I do.  Fuel cell wouldn't be too bad but all of that tubing under the car is so beat up now I'd end up just doing that again from scratch.  It's months of work in total and then the car is not as practical for normal use, I don't think I'll cage another one of my Subarus again.  Especially now that they moved the Dakar to your side of the Atlantic.

The long travel suspension should be easier on the body than stock suspension, but then we drive the cars a lot harder so it's a lot of stress on the body.  We will find out in the next couple years since we now have two rust free cars with long travel suspension.  So far it's been pretty good, a little separation at the rear subframe/trailing arm mounts on B's Forester that we need to deal with, but haven't noticed any problems on my white Outback.  Worst case the body only lasts a few years and then you get another one, still relatively cheap entertainment.

B and M and Z were in town over the weekend so I decided it'd be a good time to tackle the worst rear strut tower.  This is how it looked when we started:

IMG_7943s.jpg

IMG_7944s.jpg

It's hard to tell from the pictures but the bottom of that one strap isn't really attached to anything.  Really the tubing is the only reason it's staying together.

 

Then I just started cutting.  Not a lot of cutting was required, many of the seams were completely separated.

IMG_7949s.jpg

IMG_7957s.jpg

IMG_7962s.jpg

One of those projects where you just have to stop and draw the line somewhere, so I stopped there.  Basically got to sound sheet metal most of the way around and there was still enough left to provide structure and a template.

IMG_7951s.jpg

IMG_7953s.jpg

We cleaned the undercoating, paint, and rust off all the way around.

IMG_7965s.jpg

Started with a couple of flat pieces, one the shape of the wheel well, the other just in front of the gas filler.  Then curved a piece of steel for the main strut tower.  All 1/16" 4130.

IMG_7971s.jpg

IMG_7969s.jpg

Added a couple more pieces to close it up.  Tried to make the wheel well a little bigger than stock for plenty of tire clearance.

IMG_7978s.jpg

IMG_7993s.jpg

Here is how that looked from the wheel's point of view.

IMG_7974s.jpg

IMG_7983s.jpg

IMG_7994s.jpg

Still need to make the wheel arch and finish fitting at least one spot.  Overall this went much faster than I thought it would.  Saving the cardboard templates for the other side, we'll have to do the driver's side also before the Vegas to Reno.

 

B patched up this hole behind the rear tire.  That was a lot more work than it looks like.

IMG_7998s.jpg

 

Z has the AGX struts on his FXT now.  We didn't get time to try them out on the whoops but I'm curious to see how they work and hold up.  He does have a little tire rub on all the spring perches.  He hammered them up.  The driver's side rear was the worst though, he took that off, slotted the holes, and welded plates on to shift the spindle away from the spring perch.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×