Jump to content
Ultimate Subaru Message Board

87 XT idle issues. Dies when in gear.


Recommended Posts

I am trying to fix an insanely irritating idle problem on my 87 XT. EA82T engine MPFI. Its the one that sat for 17 after my dad fixed the heads and I recently got running. When it idles it wanders by about 200 RPM either way. The main big issue is that when it is in gear (Auto Tranny) it dies if you don't feather the throttle, as you can imagine that would make in town driving a pain. I have checked all the vacuum lines to the best of my knowledge. Scoured the shop manuals i have for the 86 year. Cleaned the idle air screw and the EGR air bypass solenoid as I originally thought it was the IAC valve. I have tested and replaced the vac line to the tranny from the intake manifold. And replaced the vac hoses from the pressure ports on the front of the throttle body. I cleaned the main throttle butterfly as it was suggested that that being dirty could cause this issue. I have triple checked the timing both valve and ignition. The only other thing i can think of it might be is the Aux Air Valve on top of the thermostat housing. I had pulled the electrical plug from it when it was idleing cold and it made no difference. It was my under standing that if you do that when its idling cold there is supposed to be a major idle change? I sort of suspect that it has to be a vac leak somewhere, because the engine gets kinda hot despite an upgraded cooling system and new thermostat. I have been beating my head against the wall about this problem for almost a month. If any of you can help me I would be forever grateful.

Link to comment
Share on other sites

Just throwing this out there.  Could be an airflow meter problem.  After all these years that "flexible" air intake hose isn't.  Check for cracks and insure ALL the smaller hoses are still attached. 

 

Many years ago my 85 XT turbo would just quit running.  Eventually discovered a ground wire attached to the intake manifold, right side , was corroded.  Whenever the ground was lost, the injectors stopped firing. 

Link to comment
Share on other sites

Warm to operating temp in park. Put foot on brake, no change just wanders the 200rpm like in park. I shift to drive or reverse, engine immediately begins to struggle then dies without throttle added. If I add throttle it runs as it should. If it needs to idle while in gear, like at a stop light the engine struggles then dies.

Edited by SiriusBlack
Link to comment
Share on other sites

Positive crankcase valve ?

Everyone needs to know where this $5 service replacement consumable is ....at the back side of inlet manifold below throttle body. It takes in all the fumes from the 5/8 ID hoses off the rocker covers and all MPFi EA82 blocks have extra take off turbo side, back of block near knock sensor.

Is really just a poppet valve that normally will open on deceleration I think, sucking crank case fumey air. Can carbon up and leak air that can cause sh177y idle

Also, while you are chasing problems maybe make a block off plate for EGR valve as these usually block up with soot and can cause intake throttle bypass air. I had one cause weird issues

Link to comment
Share on other sites

I am still running tests. I finished cleaning the egr valve, but haven't run it yet. I still need to block the PCV valve and test. The plug that runs to my coolant temperature activated sensor behind the intake manifold has its wires frayed right next to the plug. Does anyone know if I can acquire a new plug for that anywhere? Also will it hurt anything to just delete the egr solenoid valve that's under the intake plenum?

Link to comment
Share on other sites

Two pin plug?

You might need to find a good donor plug and wires to splice to existing wires if you can't source replacement from an EFI specialist who may stock a remedy for you.

If you delete the solenoid you may throw an ecu fault code.

Some wire a resistor between the two pins so as not to.

If you can make a blocking plate as a gasket to install between EGR and manifold, seal it also, eliminates EGR completely from your diagnosis steps

Link to comment
Share on other sites

My coolant temp sensor appears to be fine. It was the knock sensor that has frayed wires. I replaced the PCV valve and cleaned the egr valve. Double checked my vacuum lines again. Still no luck. I'm going to put a fuel pressure gauge on next and check that. In the meantime any other suggestions would be great.

Link to comment
Share on other sites

42 minutes ago, SiriusBlack said:

I'll be sure to check that too. Also, it was suggested that I see if I can get the car to tell me what's wrong with the diagnostic codes. It doesn't have the ECS light on the dash lit up, but how do I get the ECU to spit out codes?

here's a link for reading codes.  I'm not sure where the test connectors are located on your vehicle.

https://www.troublecodes.net/subaru/

searching this website for ECU codes/connectors may bring up more specific info 

 

 

Link to comment
Share on other sites

And while you are looking at TPS take note if the wiring just 30? mm from TPS has a three wire, possibly round, take off plug at all, something plugged in or not

AND how many wires to TPS itself

I have had three combinations I think.

Also think yours may be the 86 wiring, ECU etc flapper AFM likely it is TPSwitch not TPSensor as listed in diagram above

Link to comment
Share on other sites

6 hours ago, DaveT said:

The LED for the codes is on the ECU.  On "regular" [non XT] the ECU is bolted to the steering column.  You have to remove the plastic cover to see it.

On the XT the ECU is mounted in the trunk, just forward of the trunk lid. 

I will definitely check my TPS, as I recall mine has a rectangle connector, that probably goes into the wiring harness with the 2 large round connectors.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

×
×
  • Create New...