Regardie Posted October 11, 2011 Share Posted October 11, 2011 Hi All, I am looking for the install directions of the OEM Fog Light Kit for the early 2nd gen Legacys, not GT, or Outback. I know AK-Brando posted it several years ago but the links to his images are now broken. Has anyone saved his scans or might have a copy they could post? I recently purchased a nice set of projector fogs for my 97 L and would like to do as close to OEM install as possible. The fogs came with enough wire pigtail after the connector so I have some wire to work with there and I have a dash fog light switch from a u-pull-it trip last year, I just need to know the path to tie it all together. John Quote Link to comment Share on other sites More sharing options...
Fairtax4me Posted October 11, 2011 Share Posted October 11, 2011 Did you get the relay as well? I just hooked up a set in my car a few months ago. It's not hard. I can look at the wiring tomorrow and tell you where to hook up what, but you need the relay. I think it was only a 4 pin? relay though, you can usually buy those pretty cheap at a parts store if you don't have one laying around. BTW, before you install the lights make sure the adjusters work. Mine came off a junkyard car and the adjusters were full of sand. Had to remove the lights and disassemble and clean the adjusters then put everything back on so I could aim them. Quote Link to comment Share on other sites More sharing options...
Regardie Posted October 11, 2011 Author Share Posted October 11, 2011 Did you get the relay as well? I just hooked up a set in my car a few months ago. It's not hard. I can look at the wiring tomorrow and tell you where to hook up what, but you need the relay. I think it was only a 4 pin? relay though, you can usually buy those pretty cheap at a parts store if you don't have one laying around. BTW, before you install the lights make sure the adjusters work. Mine came off a junkyard car and the adjusters were full of sand. Had to remove the lights and disassemble and clean the adjusters then put everything back on so I could aim them. Good point about the adjusters. I bought a generic fog light wiring kit from AA that has a relay, in line fuse and lighted switch. I was planning to use the wire and relay only and try to hook it up to the right places in the fuse box. I have some misc. harness wires that I think I can harvest pins and sockets. I also ordered four of the insert nuts from the Subaru dealer so I have some place to mount the lights on the bumper beam. I have and can read the wiring diagrams from the FSM, so I know what the factory installed system should look like. I just wanted to compare the dealer installed system wiring to the factory and see how the dealer install went. John Quote Link to comment Share on other sites More sharing options...
Suzam Posted October 11, 2011 Share Posted October 11, 2011 PM (private message) me, I have scans of the original installation instructions that came with OEM Subaru fog lights for the 95-97 model years. Quote Link to comment Share on other sites More sharing options...
Regardie Posted October 11, 2011 Author Share Posted October 11, 2011 PM (private message) me, I have scans of the original installation instructions that came with OEM Subaru fog lights for the 95-97 model years. I would PM you but I can't at this point, it doesn't seem to be enabled for me yet. I just joined USMB because I found a post about this in a Google search. I spend most of my time at SL-i.net and a little at NASIOC. AK-Brando who had scans in the thread from maybe 2004 or so hasn't been on since 2010. I found an Ebay sale of the kit recently with a picture of the first page of the instructions so I know what was in the kit, but I don't have the run wire here, splice wire there part. I think the scans could be assembled into a pdf and posted to the manual section here so if anyone else wants instructions they can find them. Regardie Quote Link to comment Share on other sites More sharing options...
Suzam Posted October 11, 2011 Share Posted October 11, 2011 I sent you a PM with my email address. Let me know if you don't get it. If I figure out how to get a file posted in the manuals section I will submit it. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.