johnd911

who has the NTK's?

been using the non foulers for over 60,000 miles with no problem till now, new set didn't help. Light NEVER goes off, gonna try to find the sensor online. Thanks

blow over a grand ? on a 300,000 mile car?

reason I think it may be the sensor ($100 gamble) is the code never disappears, the CEL is always on. None of this off again and back on stuff, just on all the time.

Dealer is useless, they want to put in Cats. It could be a leak possibly, my hunch is a gone rear sensor. Are there any sensor tests? resistane, etc. in the service manual? or is it just a replace and hope. If it ever get dry here in Buffalo I can do the leak looksee, but have nothing more than a floor jack.

best source for them? thanks

Cats have been replace 3 times already, just put in a cheap Knock sensor, and all of a suddent eh 420 code pops up and the antifoulers don't get rid of it anymore, coincidence? The fouler things work great, have been using them for years, just been replacing them everytime the code pops up.

291,000. Engine was rebuilt at 219,000 due to a disintegrated crank bearing. The antifoulers got rid of the 420 code every single time it appeared. The rust out, so I replace them everytime the code comes back. This car gets the best care because it is my personal and work car. Last sensor was put in 40,000 miles ago, Subaru part.

it's the 420 code for the rear sensor.

I drive 1000 miles a week and am sick of these CEL codes, I have used the plug antifouler fix for years with no problem, now it doesn't work anymore, about 70k on the current sensor. Is it the sensor that finally bit the dust or should I try the electronic fix, which I can't find anymore anywhere. I have a 2001 Outback Auto, Help, inspection due in a few months. If I have to replace the sensor, do I HAVE to get an OEM ($$) one. Thanks people.

Also: i took out the idcle control valve, it moved freely, even swapped it out with another one to no avail. Wires, plugs, filters etc have all been changed...

Item:93 legacy automatic. what was done: idle control valve was adjusted, throttle stop screws (both) have been adjusted, and throttle position sensor has been adjusted. Why: because when leaving idle with the ac or defroster on, 50% of the time it stumbles big time right off idle. With the ac and defroster off, it's fine or the stumble is so minimal that it's no problem. why was everything adjusted: because the mechanic didn't know better. Highway mileage is around 24-25 and it drives fine. Car has 200k on it with no other problems. So basically I have a rough idle and stumble off idle 50% of the time when the ac or defroster are on. And all these things that should never be adjusted have been. Anyone know where I can find info on how to properly adjust these things? I know the lower stop screw on the plenum should NEVER be touched etc. I'm assuming nothing is set to proper adjustments anymore. The error codes vary depending on what is fiddled with. Usually coded dealing with improper signals sent to the various screwed up components. No codes until all this fiddling took place. Any help would be greatly appreciated. thanks

any differences in the engine with the 2005 new model ? or is it the 2000-2004 with the new head gaskets. Also, didn't the 2.2's after 1997 loose some of their bulletproofness? I was thinking of maybe a 2.2 up till 1999, but can't comment on that version 2.2 seems the higher compression and interference design may affect it's long term life compared to the earlier 2.2's. remember, I try to get over 200k or 300k so little things matter. I use them for work driving.

I tell ya, the best legacies were the 92-95's. I won't go near a 95-2003 outback. Anyone know how these 2005-present are holding up under high mileage.? When i get a legacy, I usually put 200k on it after I get it. So I am used to the bullet proof nature of those 92-94's.

I'm a real good expert on 92-94 legacies, have done engine swaps, repairs etc. without ever having to see a mechanic. My 93 wagon has just hit 400k. I love the 2.2 engine but am having a hard time finding rust-free low mileage 93-95 wagons. I kow the 2.5's were crap headgaskets etc. Anyone know if the 2004 or later motors have eliminated the head gasket problems? How are the 2005 and later engines? Rather than get a low cost but very high mileage (with rust) 93-95 I may be interested in looking for a 2003 or later, but these 2.5's may not have the gasket problem fixed. I'd like to get an off lease 2004 or later and keep it for 250k, but am really leary. If I could find a 95-99 legacy wagon with moonroof (wife wants silver or white) from the south that would be great , but finding a low mileage one is tough. Any opinions greatly appreciated.