citabrickr

I have rust in the exact same spot on my 02 Outback, as well as a 4" patch right on the left rear wheel arch peak on the quarter panel. Both began as bubbling paint. No other rust anywhere on the car.

I had this exact problem on a CCR rebuilt engine within the first 1000 miles, top left front and right rear both had pooling oil that would run down the back and drip on the exhaust, didn't have the problem long though as that engine finally threw a rod thru the case (making a bigger leak...). Their offered solution at the time was to send it back to them so they could fix it but it wasn't that appealing to pull the engine again and be carless.

Still haven't had time to clean it but have looked it over again a little closer. Oil pressure switch is dry as a bone as is the whole "center" of the top of the engine. Power steering pump is on the right front and that area is dry, no pump or hose leaks. Valve covers are bone dry. The left (driver) side is the worst, with about half a dixie cup of oil (not a small amount!) starting right about where the A/C compressor mount is aft to the knock sensor, that whole area from the head gasket toward the center of the engine is damp, with oil pooling in the stiffening webs, dripping down the back of the head on to the exhaust. Outboard of the head gasket towards the cover is dry. The right (passenger) side is much less, only a small amount (about the amount that would fill the cap off of a bottle of oil) on the aft side, same as the left, from the head gasket line inboard in the webs. PCV area is bone dry, valve cover is dry. Not looking forward to having to tear this thing out on my time, be carless waiting for what may be a roll of the dice replacement under "warranty" that may have operational issues like the other poor bastard posted on his 2.5 thread.

I'm an aircraft mechanic and inspector, I know all about documentation. I got an engine, a lot dirtier than I expected for $3700, some gaskets in a bag, warranty papers and a copy of the bill. Now off to get some brakleen...

This thread is giving me a virtual heart attack having just posted about my "new" CCR engines oil leak on a two month old engine....

Got a reman from CCR and installed it in my 2002 OBW October, have about 6,000 miles on it and have an oil leak on both sides of the case near the head gasket seam, on top of the engine, left side front and right side rear, left front is the worst. It's enough on the left side that it is pooling in the case webs and running back down the head onto the exhaust causing a lot of stink. Not very happy, although they seemed concerned enough to honor it under a warranty...sortof...I just have to take it out and put it back in... Anyone have any idea what it could be besides a cracked case? The wetness starts at the actual gasket seam between the heads and case but I'll need to clean it off well and check again for a better guess. Not much on top that could be leaking that I know of.

Yes, it definitely has a bulb....the console and dash display of the shift position is redundant in the 02 OBW. The 37 doesn't fit, it's too big, just like the guy in the one link found out ( his solution was to just push (force) it in harder) and the other guy never gave a bulb number.

I do have the bulb out, it is not a standard size in either an auto parts store or radio shack, that's why I was hoping someone knew the number, same as some of the instrument cluster bulbs.

Anyone have a part number and where this can be obtained? Thanks!

I just went thru this myself, used a slightly more barbaric approach. Soaked the engine/trans joint with Kroil, was initially using a sharp chisel between them but that's not how I got the initial separation. Had the trans jack supporting the trans and would jack the engine up till it was maybe a half inch high then immediately dumped the engine hoist dropping the weight of the engine sharply till I got a separation. Noticed the old engine and new engine had a small amount of corrosion in the exact same spots on top of the bell housing.

Me again....I probably should have doine a search first, I think I already have my answer. I'm just trying to justify parting with $3K on an engine with only 74K on it....sigh

Hello, Was wondering if anyone has experience with CCR Engines in Colorado. http://www.ccrengines.com/ They were very helpful on the phone making sure I explored all avenues before buying an engine, including giving me a recommendation for a local diagnostic guru. They easily spent 20 minutes on the phone with me answering all my questions. They seem to do an A-1 quality job and since I have pretty much run out of ideas, I think I may be going for an engine after all. I don't have the time to disassemble and play with my engine, I'd rather just get a plug and play, I'm pretty sure I can do the transplant after looking under the hood and perusing the service manual, looks like a long afternoon of work, nothing scary. Opinions?

Ok, here we go again....2002 OBW 2.5 SOHC EJ251 Phase 2 sticker under the hood says "Intake = 0.010" , Exhaust 0.015", the Alldata service manual instructions are: Intake; 0.20 ±0.02 mm (0.0079 ±0.0008 inch) Exhaust; 0.25 ±0.02 mm (0.0098 ±0.0008 inch) quite different....anyone know which is correct? If the tighter is allowed, I'd like to go that way to try to get rid of the damn noise this thing is making. Thanks, John

Hi all, hopefully someone knows of a NON-DEALER shop in North NJ that can actually diagnose and repair Soob engine issues, feel free to post or PM me. Love my car, hate all the dealers! Thanks in advance! John

I had the front brakes and rotors replaced about 20k ago because there was vibration with heavy braking. A week after that, a clicking sound started when i lightly applied the brakes If you got aftermarket pads put on they probably left the shims out, never seen aftermarket pads come with them. They are available from the dealer but they will tell you it's a special order item. They do come with factory pads, which are $$$ but worth it. Get a seta nd have them put on with the shims, your clicking will be gone. JT:drunk: