Jump to content
Ultimate Subaru Message Board

Search the Community

Showing results for tags 'strangeinnerpad'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


  • Welcome to the USMB!
    • Meet n' Greet. Your USMB Welcome Center
    • Members Rides
  • Older Generations of Subaru's 1960-1994 Except Legacy and Impreza
    • Historic Subaru Forum: 50's thru 70's
    • Old Gen.: 80's GL/DL/XT/Loyales...
  • Newer Generations of Subaru discussion
    • 1990 to Present Legacy, Impreza, Outback, Forester, Baja, WRX&WrxSTI, SVX
    • BRZ and its Sister the Scion FRS/Toyota GT86
    • Crosstrek "XV"
  • Marketplace
    • Ultimate Subaru Store
    • Products for your Subaru
  • Upgrading and Racing Discussion
    • Performance Tech Forums
    • Subaru Modifications
    • Subaru MotorSports
  • Ultimate Subaru Repair Manual-The Knowledge Base of USMB. Complied posts and writeups to common problems and projects.
    • Submit a Tip or Mod to the USRM
    • Product Links and References
    • The old Ultimate Subaru Repair Manual
    • Engine
    • Engine Electrical
    • Transmission, Axle, and Brakes
    • Heating and Cooling systems
    • Body Exterior
    • Interior / Body Electrical
    • Stereo tips and tricks
    • Offroad Modifications
    • Suspension and Steering
  • Off Topic Areas
    • Shop Talk
    • Alternative Vehicles (non soob)

Product Groups

  • Member Accounts
  • Ultimate Subaru Decals
  • Subaru Parts
    • Weber Carbs and Parts
    • Used Subaru Parts

Find results in...

Find results that contain...

Date Created

  • Start


Last Updated

  • Start


Filter by number of...


  • Start





Website URL







Full Real Name


Ezboard Name




Found 1 result

  1. Hi all - this is my first post. There are a few things that I have questions about - regarding my wife's 2012 Impreza Wagon Ltd. This first posting is regarding the front brake pads/rotors and my replacement of both yesterday. I purchased aftermarket rotors and ceramic pads ($120.00) total to replace my wife's front pads and rotors. She has 50,000 miles and though the brakes have lasted well, there has been a shimmy upon braking from the front end that has bothered me - and has been evident for the past 20,000 miles or so. I have had them inspected and they have always gotten a green light. I have known that the pads needed to be replaced soon - so yesterday I went about replacing the whole lot - just to be sure my rotors weren't warped, I replaced the pads and rotors. To my surprise, the inner pad had a graduated wear pattern on it. I have attached photos here as well to better illustrate this strange design. I am by no means an expert in braking systems of cars - though I have replaced my share of pads and rotors (my other car is a Mini Cooper S 2007) - front and rear. My experience has always been that the pads are flat on the rotor surface - interior and exterior. When I removed the pads on the Subaru, I found that the outer pad was as expected - but the inner pad had a 'graduated' shape to it - with a center that was raised above the outer surfaces - and this of course made the wear on the inner surface of the rotor gauged as well in relief. So, if the rotors were in good condition still (IF), new pads would not be able to be installed regardless - because of the new surface shape of the inner part of the rotor. I hope I'm making sense here, but wondered what the purpose of this design is on the part of Subaru - if anyone has any insight into this. Thanks! Lorne Next research on this forum and possible new post (depending on if I can find more information about it) will be regarding a start issue - when the engine is warm - car does not restart. And THIS issue occurs on our 2012 Impreza and my sister's 96 Outback.
  • Create New...