January 15, 200719 yr is it possible to take out the front cv axles with out the fluid leaking all over the place? im going to drift my car, but i dont want to mess up my tranny and was wondering if this is possible?
January 15, 200719 yr Yes, you can remove the axles. The transmission stubs have seals independent of the CV axle, it's not like the rear center drive shaft. You don't need to remove fluid. Todd
January 15, 200719 yr Author Yes, you can remove the axles. The transmission stubs have seals independent of the CV axle, it's not like the rear center drive shaft. You don't need to remove fluid. Todd ok heres another question, if i rerplaced the cv axles(which i did) and i didnt get new seals, would that cause the tranny to leak fluid? because thats what is happening now. i was thinking ti was the tranny front seal but iono
January 16, 200719 yr Author the connection of the bell houstong or tranny (w/e its called) where it connects to the engine
January 16, 200719 yr Could be leaking from the input shaft seal, or could be leaking from the rear main seal of the engine.
January 17, 200719 yr Author and neither of those are related to the CV axles. Todd true, but is there a possibility that it COULD leak from the cv axle seals?
January 17, 200719 yr true, but is there a possibility that it COULD leak from the cv axle seals? it is possible but the rear mains on these like to have a hissy fit after many years and many miles on them. I've had a couple gen 1s that have had a weep from the input shaft but the rear main seal is usually the main source of a leak. Replace it because if you don't, it'll eat your clutch up and then you'll have to replace it anyways.
January 17, 200719 yr true, but is there a possibility that it COULD leak from the cv axle seals? Yes, but he was referring to having all the fluid run out by just removing the axle. If the seals were leaking, they would leak with or without the CV/axle. I 2nd that it is the rear seal. Todd
January 17, 200719 yr im going to drift my car Does it still have the EA engine in it? Or is it snowing or something?
January 17, 200719 yr Author Does it still have the EA engine in it? Or is it snowing or something? no its just a semi built original engine.
January 17, 200719 yr Author how can i remove my tranny w/o having to remove mt bolts from the exhaust mani.? im scared to try and remove them for the fear that i might break the bolts, and have to get them drilled out n replaced or can i just pull out the engine and l leave the tranny on the car? what would be the more safer and easy way to go?
January 17, 200719 yr The exhaust has to come off, whether you drop the tranny or yank the engine. It's especially necessary to remove the exhaust on these cars because they have no cats (the non-Cali ones anyway) and thus the manifold assemblies reach back farther than the new Subarus. Use lots of PB Blaster and be very careful. Do it slowly. Worst case scenario, the studs will unscrew out of the head with the nut, and then you can just screw them back in and Loctite them.
January 17, 200719 yr Author The exhaust has to come off, whether you drop the tranny or yank the engine. It's especially necessary to remove the exhaust on these cars because they have no cats (the non-Cali ones anyway) and thus the manifold assemblies reach back farther than the new Subarus. Use lots of PB Blaster and be very careful. Do it slowly. Worst case scenario, the studs will unscrew out of the head with the nut, and then you can just screw them back in and Loctite them. hmmm.NEVER THOUGHT ABOUT IT THAT WAY!
February 19, 200719 yr SHIFT: CLEAR YOU PM INBOX. Thanks, Ennio hmmm.NEVER THOUGHT ABOUT IT THAT WAY!
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now