ivans imports

a used clutch ? you can get a clutch kitt for about 150 $ i like the luk clutches i do have some used ones but do not recomend one new is best

A used crank if its checked to make shure is ok i have been sending them to be turned down and have had good sucsess out of 8 cranks they saved 4 i whould get it compleate with the rods as matched set mind you how mutch for rebiuldable short block ? i sell a rebiult short block for 1500 to shop and 2000 to customer resurfaced crank done ready to run give you a idea

for what year and model ?

found 5 of them in good condition do you still need them ?

front five speed ? large spline or small splines deul range or push button trans

have the whole car and some extra doors

have tons but need to know grey or black what tip design i think there are 3 different ones do you just need a set or a specific set ?

hey how do I upload photo albums from photo bucket?

how do I navagate and find my threads

how many do you need ?

i can dig some up do you whant a whole engine i have a very good one with ea82 carb on it runs very well i will get some pushrods together for you anyway

i do it not running because air gets traped make shure you have the rad vent cap open on right side of rad top fill trough the rad cap till comes out vent cap with no bubbles helps to have the front end up a bitt takes some time fill wait fill wait it may have a slight bitt of air in heater is ok when your confedent you have most of the air out run it with caps on till rad gets hot and fans cycle then shut off let cool down and recheck rad level should hold about 6 L of coolant if still haveing problems with heater gentaly losen the top heater hose so it leaks a bitt will alow air out [not runnig ]

i found one has a bent shaft but electronics are ok

i have a non turbo one no turbo trans at all sorry bud

I have some ? are they the same as ea 81 ether way i have some think i have 5 or 6 of those engines. Did they bend ? i have one that sat and valves were sticky and bent pushrods when tryd to start.

i modd them up a bitt you can put ea82 turbo rods and pistons in it helps alot. Use a soilid lifter block the one with extra two head bolts. Theese engines will rev higher than the hydroilic ones you can also use a 2.0 ej piston but have to remove the piston pin bushing. I also like to put the ea82 tbi onto them if has turbo pistons can go tbi turbo thiss works well to but is diffacult to set up my 81 brat is tbi with full deul exhaust pulls about 40% better than my 80 brat with ea 71 dont use the 1600 pistons they have weak ring lands and break when pushed above 7000rpm use a piston that has the thin ring on top ring theese are alot stronger and hard to break i have some ea 81 parts still mostly crank and rod assemblys i save them for airplane guys

i will look agian and c if i have 4 that are ok

i'm 80 a hour and gess 10 hours head surface x 2 150 and head gaskets valve cover gaskets timing belt water pump coged idler pully oil/ fillter coolant and any other thing we might have missed gess about 2000 $

is youa gona catcha soma fishas or whata's hey i got your car to be 3ft taller just added snow lol

need a job ? had to find somone who uses there head

no sorry i use the 84 wagon rear seatbelt for my 80 brat have no bumpers sorry dude

ok i will dig them up for you might take me a bitt is the local carival thiss weekend in my town goto take kidds out

perty hard to find i may have some but under 3ft of snow i'm fairly shure i have a ds but most dident have a ps side mirior unless they were gls i used the 84 miriors on my 81 brat they sitt on a angle but look way better and i have lots of thoose