simbey1982 Posted March 30, 2005 Share Posted March 30, 2005 Where the heck is the ECU for a 90 legacy. Thanks Cory Link to comment Share on other sites More sharing options...
gravelRX Posted March 30, 2005 Share Posted March 30, 2005 Buried under the plastic behind the steering column to the left. IIRC. No, the easy one isn't it. That's the TCU for the automatic transmission. If yours does in fact, have an automatic tranny. Jay Link to comment Share on other sites More sharing options...
simbey1982 Posted March 30, 2005 Author Share Posted March 30, 2005 yeah i figured....doing a AT/MT swap.....the one in my impreza is under the floor board...oh well here i go... thanks Link to comment Share on other sites More sharing options...
Legacy777 Posted March 31, 2005 Share Posted March 31, 2005 for further reference http://www.main.experiencetherave.com:8080/subaru/images/ecuhide.jpg Link to comment Share on other sites More sharing options...
91LegWagon Posted October 25, 2005 Share Posted October 25, 2005 Josh, I just printed out your picture on the ECU location which appears to answer the thread I just posted. About a year ago when I started this engine swap project (I got side-tracked) you answered my question on electrical issues associated with swapping a 90 Legacy engine (with Auto Trans) into a 91 Legacy with a manual transmission. You suggested swapping the MAF, ignitor and ECU from the auto trans engine (90 Legacy) into the 91 where I am retaining the manual transmission. I have completed the engine swap except for the ECU. Any other suggestions on sensors, etc.? for further reference http://www.main.experiencetherave.com:8080/subaru/images/ecuhide.jpg Link to comment Share on other sites More sharing options...
Legacy777 Posted October 26, 2005 Share Posted October 26, 2005 Refresh my mind on what setup you're doing. Basically you want to keep the sensors associated with the ECU. The sensors in question are: MAF Sensor IAC Valve Injectors The wiring harness of the car that's going to receive everything will also play a role in which ECU, Hitachi or JECS you use. Link to comment Share on other sites More sharing options...
91LegWagon Posted October 26, 2005 Share Posted October 26, 2005 Josh, I am swapping an engine from a 90 Legacy with AT into a 91 Legacy with MT. I am keeping the MT. I got the ECU swapped yesterday. I also swapped the intake manifold and injectors, MAF and ignitor from the AT car into the MT car (91 Legacy). Now the car will start and run. Haven't driven it yet. Looks like I need to swap the IAC. Previously you had mentioned an AT/MT jumper on the ECU. I opened up one the ECUs and didn't see anything that looked like a jumper either inside or on the connectors. I am assuming I need to change the jumper from the AT ECU for a MT. Any idea how I can locate this jumper assuming it exists? Bob Link to comment Share on other sites More sharing options...
Legacy777 Posted October 27, 2005 Share Posted October 27, 2005 I'm a little confused. Which ECU are you using, the Hitachi (MT) or JECS (AT)? If you swapped the AT ECU in, you really didn't need to do squat except swap MAF sensors. When I say jumper, it's just a wire going from a certain pin on the ECU connector to ground. I'm still unsure of which ECU you are using, so I don't want to recommend anything yet. Link to comment Share on other sites More sharing options...
91LegWagon Posted November 1, 2005 Share Posted November 1, 2005 Josh, I swapped the AT ECU in and the car runs fine. So I'm happy. Thanks for your help. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now