I have an intermittent rapid clicking coming from behind the dash on my 2000 Legacy L. Sounds like a relay or solenoid rapidly cycling. When I play with the turn signal switch I can get it to stop. Anyone know if there is a flasher unit or control module that may be the culprit? Any suggestions or ideas are appreciated.
Welcome to Ultimate Subaru Message Board, my lurker friend!
|Welcome to Ultimate Subaru Message Board, an unparalleled Subaru community full of the greatest Subaru gurus and modders on the planet! We offer technical information and discussion about all things Subaru, the best and most popular all wheel drive vehicles ever created.
We offer all this information for free to everyone, even lurkers like you! All we ask in return is that you sign up and give back some of what you get out - without our awesome registered users none of this would be possible! Plus, you get way more great stuff as a member! Lurk to lose, participate to WIN*!
* The joy of participation and being generally awesome constitutes winning
** Not an actual guarantee, but seriously, you probably won't regret it!
Serving the Subaru Community since May 18th, 1998!
2000 Legacy clicking sound from behind dash, turn signals?
Posted 31 March 2013 - 04:38 PM
Next time it happens get out and look at your turn signals, preferably in the dark with the lights off.
When it happens does the lights or brakes have anything to do with it?
Next choice would be to drop the knee panel on the drivers side and see if you can get a better idea of the location. There are several things that can make that kind of noise under the dash. Turn signals may be related but not the problem.
Posted 05 April 2013 - 02:47 PM
Update: Lights don't make any difference, brakes no difference. It always happens after turning on the left turn signal. The only way to turn it off is select right turn signal. The hazard switch also does not make any difference. The most likely culprits are the Turn signal and hazard module, and the turn signal/light switch assembly.
Posted 05 April 2013 - 08:31 PM
Are all of your turn signals working?
Sometimes a bad connection, corrosion cause this.
Posted 08 May 2013 - 05:37 PM
Update: It turned out to be the turn signal switch assembly (same one that has headlights). Also changed the flasher unit but that wasn't the problem.
Posted 24 September 2015 - 06:53 AM
I was going to grab a switch at Harry's, but decided to just pull it out and see if cleaning would help. Once the switch was removed it was very easy to open up and investigate.
Before taking it apart, move the stalk around to get used to how it is supposed to feel. There is a clear cover with a tab on each corner, gently pretty this away. Next to remove is a white panel, this is held by 2 small Phillips screws on one side and 2 black trans on the other. When you pull this off, it will expose 2 small loose parts, so remove the white panel slowly. Lift the white panel off of the black assembly and the parts should stay with the black assembly. The small white loose part is the slider for the low/high beams and flasher. At the edge is a small black slider with a copper pad, this is the slider for the turn signal. Look at the white panel and you will see the brass buttons that the slider makes contact with.
I'm not an electrical engineer, but the inside of this assembly is covered with non conductive electrical lube. In the area of the turn signal slider it looks like the copper and brass have slowly worn away adding enough material to make the lube slightly conductive. I cleaned out the dirty lube. Unfortunately both of my cans of contact cleaner were dead and I didn't have a good lube to put in there. So I just cleaned it out with an old tooth brush and pit everything back together. After getting the switch back into place I was happy to hear no clicking after testing it.
Since i did a somewhat sloppy job, and i have a couple of vehicles with this same switch, I do plan on grabbing a switch from the junkyard as a spare on my next trip down. When I do, I'll get some pictures so my non technical ramblings make a little more sense...
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users