Jump to content
Ultimate Subaru Message Board

Search the Community

Showing results for tags 'stud'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


  • Welcome to the USMB!
    • Meet n' Greet. Your USMB Welcome Center
    • Members Rides
  • Older Generations of Subaru's 1960-1994 Except Legacy and Impreza
    • Historic Subaru Forum: 50's thru 70's
    • Old Gen.: 80's GL/DL/XT/Loyales...
  • Newer Generations of Subaru discussion
    • 1990 to Present Legacy, Impreza, Outback, Forester, Baja, WRX&WrxSTI, SVX
    • BRZ and its Sister the Scion FRS/Toyota GT86
    • Crosstrek "XV"
  • Marketplace
    • Ultimate Subaru Store
    • Products for your Subaru
  • Upgrading and Racing Discussion
    • Performance Tech Forums
    • Subaru Modifications
    • Subaru MotorSports
  • Ultimate Subaru Repair Manual-The Knowledge Base of USMB. Complied posts and writeups to common problems and projects.
    • Submit a Tip or Mod to the USRM
    • Product Links and References
    • The old Ultimate Subaru Repair Manual
    • Engine
    • Engine Electrical
    • Transmission, Axle, and Brakes
    • Heating and Cooling systems
    • Body Exterior
    • Interior / Body Electrical
    • Stereo tips and tricks
    • Offroad Modifications
    • Suspension and Steering
  • Off Topic Areas
    • Shop Talk
    • Alternative Vehicles (non soob)

Product Groups

  • Member Accounts
  • Ultimate Subaru Decals
  • Subaru Parts
    • Weber Carbs and Parts
    • Used Subaru Parts

Find results in...

Find results that contain...

Date Created

  • Start


Last Updated

  • Start


Filter by number of...


  • Start





Website URL







Full Real Name


Ezboard Name




Found 3 results

  1. It looks like I could use shorter studs if I remove this part. Will the y pipe bolt directly to the block? I am going to do the Weber conversion, so no need for the exhaust gas. So, is there any good reason to leave it on there?
  2. One front wheel stud is broken off of my 1984 gl 4wd. Do I need to replace the whole plate?
  3. 98 OBW w/ 2.2 240K miles The back story. Three years and 5K miles ago I performed significant exhaust repair. I replaced the rear catalytic converter, O2 sensor, center pipe and muffler all due to rust. I purchased the parts off the internet. All of them were aftermarket. I could not get things bolted together tightly so I did end up at a local exhaust shop that tightened things up for me including extended the center pipe for a $100. I am writing this up to provide some encouragement when things go bad and to provide all of the parts that will fit perfect without any trips to the shop. If I had to take this to the shop I probably would have sold the car as-is due to the cost of the repair Present day Nov 2015. I thought this would be a 5 minute $5 fix. I had a leak where the Y-pipe meets the head. I proceeded to unbolt the y-pipe with the impact wrench and snapped an exhaust stud. I was able to remove the other three with nut and stud as one piece. They were fused together due to rust. Now I needed the exhaust out of the way. Unbolting the y-pip from the front cat is not worth the pain of working on your back so I pulled down the entire exhaust for a good inspection. Things just got worse from here. One broken exhaust stud in the block. Rear stud driver side. (worst one to snap) The y-pipe head flanges where rusted out. I could see black exhaust trails flowing down the head. The three year old non-oem replacement catalytic converter (Walker 16090) had advanced rust issues on the flanges and the hanger was half rusted out. (I purchased this off Amazon and it had a 5 year warranty). They replaced it without any issue. Unable to remove generic O2 Sensor (BOSCH 15726) from the catalytic converter The three year old non-oem center pipe had a huge hole on the top of the resonator. Could not find any receipts for this one. Removing the exhaust stud There are many tricks to get this done. I had no access to welding equipment. I did not even bother with the EZ out tools because there was no way I was getting more torque then what was available before the bolt head snapped off. 1) Get a new hack saw blade and wrap one side with a towel so you can hold it comfortable. Use oil and cut the stud flush with the head if it is not already thatway. 2) Center punch the stud 3) Drill a pilot hole using a ¼ Colbalt drill bill. Drill to the depth that the other empty stud holes are at. You can measure this by dropping in the drill bit in an empty hole and wrapping tap around the bit as a marker. DO NOT DRILL TOO DEEP. 4) Now drill the hole for a second time using a 5/16 Cobalt drill bit. I used a DeWalt DWA1220 and it cut like butter. 5) Now it is time to tap the hole. I used an IRWIN 10mm – 1.25 that picked up off eBay. THIS IS A CRITICAL TIME. You need to do this by hand. Since I broke the stud located in the worst spot I had to put the tap into ¼ 12 inch extension and then insert the extension into the hand tool. I will include a picture of this. At most I was able to turn the tap 1/16 of an inch before I had to pull it out and blow the metal shavings off with compressed air and re-oil the tap. This entire process from step 1 took me 6 hours over the course of a week to complete. Do not lose faith here. This is very slow going. If you break the drill bit or the tap in the stud hole you will need a new head. Careful work here is worth it. Do the math. I also chased the other three holes. I was very surprised to see all of the shavings that came out. Cover everything in anti-seize I went with new OEM studs and nuts instead of the old fused stud/bolt that I pulled off. For $20 I thought it was worth going new. The exhaust will go on exactly as it was taken off. When it comes to exhaust parts I am generally ok with aftermarket except the gaskets used between the y-pipe and the head. Use OEM. This is just my experience. This parts list worked perfectly for my 98 Subaru Outback with 2.2 engine. The 2.2 engine is a single port exhaust. If you have the 2.5 you have dual port exhaust on the head and will need a different Y-pipe and head exhaust gaskets. Parts List (1) Y-pipe Part# 2100-58201-2. Manufacture: AUTOPART International - eBay (2) Gasket between Y-Pipe and Engine. Part# 44011AC020. Manufacture Subaru - eBay (1) Gasket between Y-Pipe and front catalytic converter. Part# 2107-00288. Manufacture: AUTOPART International – Came with the y-pipe (2) Gasket between front and rear catalytic converter. Between center pipe and muffler Part# 31388. Manufacture: Walker - Amazon (1) Flex joint donut gasket between rear catalytic converter and center pipe. Part# 31697. Manufacture: Walker - Amazon (1) Spring Bolt Kit used to connect center pipe to rear catalytic converter. Part# 35412. Manufacture: Walker - Amazon (1) O2 Sensor for rear catalytic converter. Part# 15726. Manufacture BOSCH - Amazon (1) Rear catalytic converter. Part# 16090. Manufacture Walker. (Warranty replacement for me) - Amazon (4) Exhaust Studs. Part# 800910550. Manufacture Subaru - eBay (4) Exhaust Stud Bolts. Part# 902370029. Manufacture Subaru - eBay The parts total was $255. I have 10 hours labor in this job. If I had a shop complete this work I am guessing the total would have been $1,000 to $1,400.
  • Create New...