Jump to content
Ultimate Subaru Message Board

Search the Community

Showing results for tags 'pipe'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Welcome to the USMB!
    • Meet n' Greet. Your USMB Welcome Center
    • Members Rides
  • Older Generations of Subaru's 1960-1994 Except Legacy and Impreza
    • Historic Subaru Forum: 50's thru 70's
    • Old Gen.: 80's GL/DL/XT/Loyales...
  • Newer Generations of Subaru discussion
    • 1990 to Present Legacy, Impreza, Outback, Forester, Baja, WRX&WrxSTI, SVX
    • BRZ and its Sister the Scion FRS/Toyota GT86
    • Crosstrek "XV"
  • Marketplace
    • Ultimate Subaru Store
    • Products for your Subaru
  • Upgrading and Racing Discussion
    • Performance Tech Forums
    • Subaru Modifications
    • Subaru MotorSports
  • Ultimate Subaru Repair Manual-The Knowledge Base of USMB. Complied posts and writeups to common problems and projects.
    • Submit a Tip or Mod to the USRM
    • Product Links and References
    • The old Ultimate Subaru Repair Manual
    • Engine
    • Engine Electrical
    • Transmission, Axle, and Brakes
    • Heating and Cooling systems
    • Body Exterior
    • Interior / Body Electrical
    • Stereo tips and tricks
    • Offroad Modifications
    • Suspension and Steering
  • Off Topic Areas
    • Shop Talk
    • Alternative Vehicles (non soob)

Product Groups

  • Member Accounts
  • Ultimate Subaru Decals
  • Subaru Parts
    • Weber Carbs and Parts
    • Used Subaru Parts

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests


Full Real Name


Occupation


Ezboard Name


Referral


Biography


Vehicles

Found 4 results

  1. SOLVED Body: '98 OBW Current motor: EJ251 block, EJ25D heads (rings are letting oil be consumed, and there are sounds of the beginnings of rod-knock) Newer motor: Reman EJ253/251 block, EJ25D heads. Hey folks. I bought a reman block form subaru. EJ253/251 block for a 2003 forester. Mating it with EJ25D heads to replace my current hybrid (EJ251 and EJ25D heads). Everything is just about ready to go except the PCV system. The newer block has what appears to be a threaded-in bung to accepted a threaded PCV. Being that the intake I'm using is for the heads, it already has a PCV. Has anyone put a newer block into an older system and routed the PCV system successfully? The old-style is just a pipe that comes out of the block, with the vinyl tubes coming off of it. They don't fit over the new interface. I'll try and get photos soon. Looking at pictures for the newer PCV, it doesn't look as if its outer diameter is the same inner diameter of the older crankcase hose that would be going up to the PCV on the intake. a Thoughts and advice much appreciated. Greg
  2. It looks like I could use shorter studs if I remove this part. Will the y pipe bolt directly to the block? I am going to do the Weber conversion, so no need for the exhaust gas. So, is there any good reason to leave it on there?
  3. The engines on my 84 gl 4wd wagon, and my ‘85 Brat look pretty much the same. Are the exhaust systems the same?
  4. Attention all turbocharged EA owners! This thread is to gauge the interest in an aftermarket replacement for your MAF-to-turbo hose. As you probably have experienced owning an older Subaru, many critical parts are no longer available (NLA), including the inlet hose on our EA81T and EA82T engines. This particular rubber hose happens to be out of production and is installed in a location that sees a lot of heat. I found the pipe on my personal vehicle had split where it joins the turbocharger's inlet and once I found out I couldn't order a replacement, I reached out to a few companies about building a replacement. The details: Replacement hose made from silicone Molded to match the contours of the OEM part Nylon reinforced for rigidity Lined with fluorosilicone to resist damage from PCV oil mist Resists degradation in temperatures up to ~500*F (EPDM rubber is good to ~210*F) CARB legal There is also an opportunity to have replacements made for all the other molded rubber PCV/vacuum hoses that are currently out of production. At this point I have a rough idea of what it will take to manufacture this part. Price will depend on how many parts are made, so this thread is for me to get an idea of how many folks here would be interested in one of these hoses. There are still a lot of variables to work out, but I'm open to comments and suggestions. So, who's interested?
×
×
  • Create New...