October 24, 201114 yr okay so i picked me up a 88 subaru turbo gl the other day for 260$ (no motor), got my ej22 and harness stripped just waiting on a couple of things for start putting her togeather (money included) haha. pretty much just need the xt6 clutch, addplate and fans pretty stoked to build my monster subi!!! has 180k on it not bad for a little car work for my girlfriends parents impreza. Three and half days of streight harness stripping, not bad for a noob. my 235/75/R15s for the 6 lug swap the ej22 should fit right up with the cross member bolts right? looks the same as my 90 loyale and thous fit right up. it being a turbo dosnt change much does it? i am open to any advice from anyone! thanks! -Prwa Edited October 24, 201114 yr by Prwa101
November 1, 201114 yr The cross member is going to be different for you. Now wether or not that is an issue I don't know. But I do know that the turbo cross member is the one that seems to be wanted, IIRC. Might want to look that up...
November 1, 201114 yr All thats needed on the x-member is to ream the holes out about 1/2" towards the center.
November 1, 201114 yr Author in the write up, "Use the EJ motor mounts, and widen the mounting holes in the crossmember slightly, somewhere between 1/4" to 1/2" on either side. A Dremel or similar rotary tool with a grinding stone works great for this. EA82 crossmember accepts the motor mount holes without widening (round EJ mounts) EJ mounts may have a centering nipple that needs to be ground off as there is no receiving hole in the EA crossmember as there is in the EJ crossmember. 3""" and i think mine is an ea82, theres no block to see what it is, but looks like surfing the web that it is a ea82T. Prwa
November 1, 201114 yr if its an ea82, which i would assume it is. since its an 88 turbo, you dont have to do the holes wider from my experience, i didnt have to do anything to the crossmember in my 92. i think thats for ea81 only that you need to adjust the holes. **info based on the Subaru EA Wiki page. showing ea81t only up thru 84 Edited November 1, 201114 yr by xbeerd
November 1, 201114 yr Author if its an ea82, which i would assume it is. since its an 88 turbo, you dont have to do the holes wider from my experience, i didnt have to do anything to the crossmember in my 92. i think thats for ea81 only that you need to adjust the holes. **info based on the Subaru EA Wiki page. showing ea81t only up thru 84 Yup, that's where I saw it too! Thanks!
November 23, 201114 yr Author Finnly got some time to start putting the lift in, got all the bolts for the crossmember undone other than one... It's striped... So another hold back, should have it finished once schools over for break...
November 23, 201114 yr Speaking of motor mounts for your EJ swap, it might be a good time to make shims described in post #9. http://www.ultimatesubaru.org/forum/showthread.php?t=72902&highlight=EJ+swap+motor+mounts Some people have problems with the mounts splitting, others do not seem to have the issue. My motor mounts lasted about 1/2 tank of gas before they split and the motor was jumping all over the place.
November 24, 201114 yr Author Speaking of motor mounts for your EJ swap, it might be a good time to make shims described in post #9. http://www.ultimatesubaru.org/forum/showthread.php?t=72902&highlight=EJ+swap+motor+mounts Some people have problems with the mounts splitting, others do not seem to have the issue. My motor mounts lasted about 1/2 tank of gas before they split and the motor was jumping all over the place. That's a very good point, and this is the first I've heard it it. Hmm so could swapping the crossmember on my GL to the legacy fix this? If its possible to do so? And sounds like its kinda a hit and miss thing that happens.
November 28, 201114 yr Author I still have the doner car a 93 leg, should I steal anything else off of it other than the ej swap stuff before I scrap it? Prwa
November 28, 201114 yr I just slipped some 1/4" rod in there on the gap side and tightened down the nut, never a issue and the round ones are prone to break
December 2, 201114 yr My motor mounts lasted about 1/2 tank of gas before they split and the motor was jumping all over the place. Did you install a proper dogbone (pitch stopper) The engine will rock around all over, and eventually break the mounts without a good solid pitch stopper. It also improves shifting since the rump roast of the trans won't be tipping up and down under Ac/Decelaration.
January 12, 201214 yr Author well got my 3" crossmember spacers in and painted (did that after the photo was taked) , just didnt have time to put it up, got those in and the tranny mounts spacers, (forgot to take a photo of those) lol and now working on the back lift, got my 4" rear strut lift from poobaru for 25$ thanks man! not bad for garage junk haha and just orderd the rear diff drop from sjr! thanks for having an awesome business! more coming soon!
January 27, 201214 yr Author Damn thous are a pain in the butt to get on! now for the other side. the diff in in the ground!
February 6, 201214 yr Author had some extra time before class so i droped by the metals shop and finished my lift not bad for the first time on the TIG
February 9, 201214 yr Uhh..... you've turned the triangulation into a parrallelogram. You may experience some rocking forward and aft from the diff. Might not matter, but worst case could pull you're driveline out of the back of the trans. You may want to rethink that mount. I'd put a spacer between the diff and the hanger instead. and only an inch. no need to drop th e front of the diff down as much as the rear. that keeps it more of a triangle. Edited February 9, 201214 yr by Gloyale
February 9, 201214 yr Author Uhh..... you've turned the triangulation into a parrallelogram. You may experience some rocking forward and aft from the diff. Might not matter, but worst case could pull you're driveline out of the back of the trans. You may want to rethink that mount. I'd put a spacer between the diff and the hanger instead. and only an inch. no need to drop th e front of the diff down as much as the rear. that keeps it more of a triangle. Well darn... Considering I already installed it.. I thought I was copying sjrs, with the tubes and longer bolts, but now that I look at it th tubes arnt 3"..... They look to be 1.5" or 2? Does that sound right? I was going to do that but, I thought I'd try something new, and didn't want to spend anymore $$ on those long bolts when I could just tack weld some metal in on my Spare time. I'll go and look at the driveline and see how catywompis it is.
February 9, 201214 yr Well darn... Considering I already installed it.. I thought I was copying sjrs, with the tubes and longer bolts, but now that I look at it th tubes arnt 3"..... They look to be 1.5" or 2? Does that sound right? I was going to do that but, I thought I'd try something new, and didn't want to spend anymore $$ on those long bolts when I could just tack weld some metal in on my Spare time. I'll go and look at the driveline and see how catywompis it is. I run 2" at the front or rear diff and 3" at the rear
February 9, 201214 yr Author I run 2" at the front or rear diff and 3" at the rear Thanks! Yeah 3" is to much for sure, its way to low, really bad angle on the drive Line. Well back to the drawing board, and back to the welding shop.
February 10, 201214 yr Author well looks like im going to make my ej addaptor plate, went into the metals shop and turns out theres a lot of 1/2" steel plates in there. plazma cutter here i come! ------ resent..... plasma cutter broken...... anyone know where i can get a ej adaptor plate for about 100$??? Edited February 16, 201214 yr by Prwa101
April 3, 201213 yr Author Well made a bit of head way in the past weeks. Got the add plate from sjr, lift completed, and starting to look at cutting the wires out of the car to fit the harness through the fire wall. Does this stuff need to go? I think it's the igniter, but not sure.
April 3, 201213 yr Well made a bit of head way in the past weeks. Got the add plate from sjr, lift completed, and starting to look at cutting the wires out of the car to fit the harness through the fire wall. Does this stuff need to go? I think it's the igniter, but not sure. that's not the igniter. It's the boost solenoid, and the dropping resistor for the EA82 injectors. It can go. Although, I would advise not to cut alot of wires out of your EA harness. You should be able to fit the EJ harness in without cutting "out" any of the EA bundle.
April 3, 201213 yr Author that's not the igniter. It's the boost solenoid, and the dropping resistor for the EA82 injectors. It can go. Although, I would advise not to cut alot of wires out of your EA harness. You should be able to fit the EJ harness in without cutting "out" any of the EA bundle. Thanks! Okay I wont cut anything out, I'd rather be safe than sorry and I understand why you say that. Could end up cutting a wire that goes to something that shouldn't have been cut. The ej harness will fit through the hole under the fender fire wall, sweet saves me time! Thanks Gloyale!
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now