murphsubaru Posted February 16, 2009 Share Posted February 16, 2009 Has anyone used the AUTOZONE CV replacement boot? This boot comes in two halves. One of my inner cv boots is split and I was thinking of tying one. Quote Link to comment Share on other sites More sharing options...
abog Posted February 16, 2009 Share Posted February 16, 2009 Personally, have never had any luck with those, easy to put on but never last very long. Quote Link to comment Share on other sites More sharing options...
Loyale 2.7 Turbo Posted February 16, 2009 Share Posted February 16, 2009 I Have never seen a Boot that Comes in Two Halves! ... ... Sounds like a Bad Idea, or it might Work just as Temporary Fix for a While... Quote Link to comment Share on other sites More sharing options...
wrongturninwv Posted February 16, 2009 Share Posted February 16, 2009 Junk. Some called a Quick Boot. Some glue together some screw together some snap together. A sort of hard boot that will not flex enough when wheels are fully turned. They will break open again and you will lose the grease you have to buy extra. Not worth your time or money. Quote Link to comment Share on other sites More sharing options...
DishMan Posted February 17, 2009 Share Posted February 17, 2009 I did not much like the look of the split boot so I went for the conventional type. If it is the outer boot you are replacing, then there is also a version that is not split but will push over the CV joint using a special cone to stretch it. Of course you still have to remove the hub, so given you have to do that it is probably not much more work to remove the axle. That also has the advantage of allowing you to properly clean and check the CV joint which is particularly advisable if it has been torn for a while. One thing I learned is that if you have the inner end pinned to the stub axle it is better to remove the pin before you try to remove the hub from the axle. I did not do that and the stub pulled out. Turned out to not be a major problem, but extra work and risk of contamination in the differential. Quote Link to comment Share on other sites More sharing options...
98obster Posted February 17, 2009 Share Posted February 17, 2009 I did not much like the look of the split boot so I went for the conventional type. If it is the outer boot you are replacing, then there is also a version that is not split but will push over the CV joint using a special cone to stretch it. Of course you still have to remove the hub, so given you have to do that it is probably not much more work to remove the axle. That also has the advantage of allowing you to properly clean and check the CV joint which is particularly advisable if it has been torn for a while. One thing I learned is that if you have the inner end pinned to the stub axle it is better to remove the pin before you try to remove the hub from the axle. I did not do that and the stub pulled out. Turned out to not be a major problem, but extra work and risk of contamination in the differential. in replacing the axle i follow this rule: first step-roll pin out; last step-roll pin in. Because stretching or ripping the boot on new axle is not an option-is it? definitely buy boot kits to refurbish your OE axles if you catch the rips early. Quote Link to comment Share on other sites More sharing options...
Sundance Posted February 17, 2009 Share Posted February 17, 2009 I stopped putting boots on a few years ago. Just isn't worth the time and effort when you compare the cost of a re-man axle. Most re-man axles are like $75 and are just so much easier to install. The only time I would consider a reboot would be a tear due to an object on a axle with just a few thousand miles on it. Quote Link to comment Share on other sites More sharing options...
Gloyale Posted February 17, 2009 Share Posted February 17, 2009 I stopped putting boots on a few years ago. Just isn'tworth the time and effort when you compare the cost of a re-man axle. Most re-man axles are like $75 and are just so much easier to install. The only time I would consider a reboot would be a tear due to an object on a axle with just a few thousand miles on it. I preffer to reboot my own axles for wheelin. The aftermarket axles are often junk, rebuild, or wholy new made in china parts. I recently replaced one that was less than a year old. Outer joint had grenaded. OEM axles are the best option, reboot them as soon as you notice a tear. Quote Link to comment Share on other sites More sharing options...
Gloyale Posted February 17, 2009 Share Posted February 17, 2009 Split boots are a band aid solution. Good to get you home on a long trip, but not much else. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.