January 25, 200917 yr Hi all, I have small oil drips coming from the right hand (passenger side) engine and make the timing belt cover a little wet. However, I'm not entirely sure where it comes from. It looks like it's leaking between the RH timing belt cover and the engine. I am going to do my timing belt within the next couple month (when I get my $$ save up) so I'm debating should I shoot for that problem. If I do, I am wondering if it's the cam seal. Any idea would be appreciate Vincent P.S. it's a 1998 Imp OBS 5MT with 182540 mi on the Eng.
January 25, 200917 yr chances are its your P/S cam seal....if your going to be doing the timing belt soon...it takes all of about an extra 15 minutes when your in there to remove the cam sproket and pull the seal out and replace....Or you could always go the other route and clean off the entire underside of the engine and give it a few days, hop back under there and see if its still coming from the same spot....the only other thing i can think of in that location is like the corner of the valve cover gasket..but my guess would def. be a cam seal...and if your going to be replacing one than i would do the other side also,and the crank seal, and the timing belt idler pulleys, and possibly the t-belt tensioner....do a search on this forum...there are tons of threads here about this......also take a look here... http://endwrench.com/images/pdfs/StepEWAug07.pdf
January 25, 200917 yr It cam be the PS pump, it can be cam seals, oil pump or main seal. Clean the engine top and bottom then watch and see where it is coming from. nipper
January 26, 200917 yr Engine is a 2.2L, interference motor... ...you have the classic right cam and crank seal leaks... when u do the timing belt, do the seals too. Now, be careful who do u send it to get it done.. not all mechanics know that subaru wet interference in 1997 and up
January 26, 200917 yr Author Sweet that's comforting, or not. I am going to try do the timing belt myself with a friend of mine. I'm new in those things but my friend has more experience though never change a timing belt before. I've been reading tons of post of how to change timing belt and also got an Alldata account so I might just going to give it a try. So here are a few of my questions 1. How hard would that be to do the cam seal? 2. Do I need to take off the timing belt cover #2 (the back one)? 3. Do I need any special tools? 4. Anything I REALLY need to pay attention at? Thank alot! Vincent
January 26, 200917 yr Sweet that's comforting, or not. I am going to try do the timing belt myself with a friend of mine. I'm new in those things but my friend has more experience though never change a timing belt before. I've been reading tons of post of how to change timing belt and also got an Alldata account so I might just going to give it a try. So here are a few of my questions 1. How hard would that be to do the cam seal? 2. Do I need to take off the timing belt cover #2 (the back one)? 3. Do I need any special tools? 4. Anything I REALLY need to pay attention at? Thank alot! Vincent Go to www.endwrench.com and go to the archives, engine section. Look at the timing belts and read to see what you have to do. The seals are easy, once you get to them. You also need to do the water pump, idler tensioner reseal the oil pump and the main seal. It sounds scary but do all that and you dont have to touch them again, unless the car makes it to 287,000 miles
January 26, 200917 yr 2.2 Liter, timing belt: http://endwrench.com/images/pdfs/2.2SingleOverWin01.pdf http://endwrench.com/images/pdfs/2.2Liter.pdf http://endwrench.com/images/pdfs/TBeltEWWin05.pdf Motor Magazine series; starts with 2.2, then moves on to 2.5: http://www.motor.com/magazine/pdfs/072001_08.pdf</p> http://www.motor.com/magazine/pdfs/082001_08.pdf http://www.motor.com/magazine/pdfs/092001_08.pdf http://www.motor.com/magazine/pdfs/102001_08.pdf http://www.motor.com/magazine/pdfs/112001_08.pdf (last one includes new-style tensioner info) Edited January 26, 200917 yr by OB99W
January 27, 200917 yr Author Thank you for all your responses. I think I have a basic idea on how to change timing belt part. On the other hand, I don't have much clue on how to replace the seal. I heard it is a PITA job. Anyways, seems like I need to get the camshaft sprocket holder (499207100) from http://subaru.spx.com/ or http://www.cobbtuning.com/products/?id=3555&rsku=0 which one is better? How do I get the old seal out and put the new one in? Thanks Vincent Edited January 27, 200917 yr by vincentmoy
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now