Skip to content
View in the app

A better way to browse. Learn more.

Ultimate Subaru Message Board

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Has anyone rebuilt their Power Steering pump.

Featured Replies

97 Legato (Legacy 2.2 auto).

 

I have a pool of ATF upper right front of the engine, obviously from PS pump, occasionally needs refill.

 

I bought a cheap OEM pump rebuild kit, but thought I better ask around before removing a basically-fine-but-leaking-a-little working part and facing pointless difficulties that can be worked around merely by adding ATF every few weeks or so.

 

Is the remove-rebuild-replace a couple hour thing?

 

Thanks

 

mpergielwalkermi97legate99forester08forester

these things leak all the time at the oring between the reservoir and pump, i just did one a couple weeks ago. no need to mess with the pump at all, just remove the reservoir and replace the oring underneath. very simple and can be done in 30 minutes.

A lot of the ones I get are the rubber coated metal gasket which requires dis-assembly. A used on eis about the price of the rebuild parts at the dealer(about 20 bucks).

 

I just install a used one. I have torn apart a few to see what the issue was.

i haven't used it on my subarus yet, but the Trans-x PS stop leak worked great in my wife's avalon. we used to have a puddle and needed to refil all the time now an occasion drip. i need to swap the pump, i already did the rack. what a pain!!

Lucas PS additive has served me very well - especially on Subaru's. But not the the pump leak that I described - the gasket - not the reservoir Oring.

 

Wouldn't hurt anything. But I wouldn't have high expectations.

Like said, the 1.00 oring seal at the bottom of the resevoir is where they usually bleed pink stuff from down onto the top of the engine. There is also washer gasket on the top side, and the oring on the bottom side.......cheap, easy to replace.

The OEM reseal kits are great.

 

The hardest part is pressing (or hammering) out the shaft and bearing.

 

Also, there is a bolt that uses a rubberized washer. It is INSIDE the pump resevior, and you must use an extension to remove and install it through the resevior cap/fill hole.

 

Many here are suggesting just replacing the o-rings on the resevior. That works sometimes, if it is just the resevior leaking. The full reseal is very easy and SOOOOOO satisfying once done.

As mentioned the OEM rebuild kits are pretty good and come with all the gaskets. In addition to the gaskets, I also replaced the bearing. It was relatively easy, just press it off and press the new one on. You just need to keep track of all the parts. Only thing I forgot was the spring behind the regulator/bypass valve on the discharge.

 

Here's some pics

 

http://main.experiencetherave.com/subaru/images/psteeringpump/

As mentioned the OEM rebuild kits are pretty good and come with all the gaskets. In addition to the gaskets, I also replaced the bearing. It was relatively easy, just press it off and press the new one on. You just need to keep track of all the parts. Only thing I forgot was the spring behind the regulator/bypass valve on the discharge.

 

Here's some pics

 

http://main.experiencetherave.com/subaru/images/psteeringpump/

Very impressive and educational. Thanks for the effort!

Interesting fact: there are two rebuild kits from Subaru for the PS pump on my Impreza. I bought them both when I did the repair and neither kit included the bearing! Just seals and gaskets. Apparently the bearing never wears out since it is immersed in PS fluid. Bearing in my pump was just fine after 140K miles, but I replaced it anyway.

 

Only problem I had was that the vanes can go back in two ways...the right way or the wrong way. Just watch how they were installed when you take the pump apart (you shouldn't need to remove the vanes....I just dropped it and everything came apart....but I figured out which way was the right way).

The kit does not include the bearing.

 

They will sell you the shaft with bearing already pressed onto it.

 

I bought a replacement generic bearing from a bearing shop and did the install myself. It's not a normal thing.

  • 1 year later...

My PS pump leaks from this area too what size is the oring anyways since I have a bunch of spare rings.

Please sign in to comment

You will be able to leave a comment after signing in

Sign In Now

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.