Search the Community
Showing results for tags 'Stop'.
Found 3 results
6 Star posted a topic in Old Gen.: 80's GL/DL/XT/Loyales...I did some searching and couldn't find much. This problem really has me scratching my head. 1982 GL Brat 200K plus on the body When the Left turn signal is on, it blinks normally as it should, however the "Stop Lamp" light will blink on the dash in time with the signal light. When the Left turn signal is on, and the Brake is applied: The LR taillight alternates between turning on/off the Lamp and the Reverse light individually, and the time of the signal light on the dash is about half the speed. It completely forgets to flash the indicator light instead. Having both Brake applied and turn signal on, the "Stop Lamp" light on the dash shuts off. The right side is unaffected and has no problems with the signal under braking or not. I have checked fuses, checked bulbs, and even swapped out the entire LR taillight assembly from another Brat; same result with the slow alternation of Brake light and Reverse light. And just FYI the reverse lights work normally when in reverse. Anybody out there have a similar problem? I'm thinking I have a bad ground or a short somewhere...
maroon_subi posted a topic in 1990 to Present Legacy, Impreza, Outback, Forester, Baja, WRX&WrxSTI, SVXHey everyone. I have a 01 Legacy Outback sedan that I just replaced the entire exhaust. The header is Emusa brand with unequal lengths. The shop only put one cat on and a Flowmaster muffler. I believe the pipe width is either 2.25'' or 2.5". The car has an awesome deep sound until you get to the muffler, and then it RATTLES. I took it back to the shop to have the hangers checked and they told me that the rattle was from so much air flow and that a resonator would help with the rattle. The real reason I had the exhaust replaced was because the Check Engine light came on, and Advanced said that it was either a bad cat or O2 sensor. The muffler shop told me that my O2 sensors were fine, and like I said, they replaced one of the Cats and deleted the other BUT when I had them check the computer, they said that Subaru's require 2 cats. My check engine light came back on after the reset and now it is shaking like crazy at stops with the car in Drive. Three questions: 1. What will get the rattle out of my exhaust? 2. Does Subaru require 2 Cats or do I need to replace my O2s? 3. How do I fix the shaking at stops with the car in drive? I am including the link for the Header so that you all can see exactly what I bought. http://www.speedyracer.com/headers/exhaust-parts/headers/1999-2005-SUBARU-IMPREZA-25L-RS-SOHC-HEADER-STAINLESS I have not gotten to do a lot of maintenance to the car yet. (I got excited with Income Tax, I know.) I have replaced the following: Air filter Cabin air filter PCV valve Fuel Filter (Octane Booster also) Synthetic Oil Change
iceshake posted a topic in 1990 to Present Legacy, Impreza, Outback, Forester, Baja, WRX&WrxSTI, SVXHi Guys, thank you for letting me post in this thread. I just owned a 1997 subaru forester (japan) stb, converted from RHD to LHD. And just recently, i am experiencing this problem: when I crank the engne it will start up easily and smoothly, but as i step into the pedal to move, the car will jerk to an almost full stop, but if i press the gas, it will still go and will never jerk again all throughout the trip. but when i pulled over at a gas station which requires to turn off the engine, it happened again as i leave the station, and keeps on happening when i turn off the engine and turn it on again, regardless it its cold or in normal temp already. what should i check to know and solve this problem? Thank you in advance guys, Im from the Philippines btw.