archemitis Posted November 2, 2004 Share Posted November 2, 2004 ok this might be an easy one for you guys, but im bored. ok so i put some mpfi into my 85 carbureted wagon. i took most of the stock stuff out of the engine compartment that i wouldn need for the efi system im runing, no more canister, ac, power steering, did away with alot of stuff. got it installed, got it all wired up, hooked up the one vac line that goes from teh car to the engine to give my heater controlls vaccume. i start the car and it starts great, then procedes to rev to the moon. i shut her down look at throttle linkages, vac lines in the way, that could have hung it up, nothing. try again and it goes to the moon again. at this point im thinking all kinds of stuff... after checking a few lines i figured out my problem. can you tell me what i did to make my car do this? Link to comment Share on other sites More sharing options...
carfreak85 Posted November 2, 2004 Share Posted November 2, 2004 Big vaccum leak maybe. Link to comment Share on other sites More sharing options...
archemitis Posted November 2, 2004 Author Share Posted November 2, 2004 im talkin pedal to the floor reving. Link to comment Share on other sites More sharing options...
subiemech85 Posted November 2, 2004 Share Posted November 2, 2004 sounds like what happened when I swapped in the ea82 manifold and carb, the cable "looks good", but was NOT seated, or the bracket was wrong for the application is the engine you put in fi or carb is it audibe rev or tach rev? Link to comment Share on other sites More sharing options...
monstaru Posted November 2, 2004 Share Posted November 2, 2004 wrong vacuum line.......... Link to comment Share on other sites More sharing options...
Wasteland Posted November 2, 2004 Share Posted November 2, 2004 Unruly truck monkey? Link to comment Share on other sites More sharing options...
MilesFox Posted November 2, 2004 Share Posted November 2, 2004 the little rubber boot on the sheath of the throttle cable came loose and wedged itself into the groove on the throtle bracket itself, keeping it from returning Link to comment Share on other sites More sharing options...
archemitis Posted November 2, 2004 Author Share Posted November 2, 2004 pedal was fine, untill it started, then it went to the floor. Link to comment Share on other sites More sharing options...
ShawnW Posted November 2, 2004 Share Posted November 2, 2004 Accel cable for the carb one still on and the length isnt right for FI? Link to comment Share on other sites More sharing options...
bajavwnsoobnut Posted November 2, 2004 Share Posted November 2, 2004 is this vehicle equiped with cruise control? if so then you had the wrong vac line hooked up to it so it would suck on that lil diaphram that controls the accelerator pedal and so it would rev to infinity and beyond Link to comment Share on other sites More sharing options...
archemitis Posted November 2, 2004 Author Share Posted November 2, 2004 that was it, i had no idea it actualy moved the stinkin throttle pedal, i thought it only messed with something on the carb. i damn near blew the car up wish i had been looking at the rpms. the heater controll vac hose comes out right next to the cruise one. you win brat rear bump stop(well used)! i trimmed the cable earlier, so it has more throw. Link to comment Share on other sites More sharing options...
monstaru Posted November 2, 2004 Share Posted November 2, 2004 aaahhheeeeemmmmmm.......i believe that is what i said....wrong vacuum line. Link to comment Share on other sites More sharing options...
baccaruda Posted November 2, 2004 Share Posted November 2, 2004 brian, isn't it past your bedtime? Link to comment Share on other sites More sharing options...
bajavwnsoobnut Posted November 2, 2004 Share Posted November 2, 2004 yeah but I nailed it right on the head hahaha hmmmm now what to do with that well used bumpstop.......... BURN IT muahahahahahahaha Link to comment Share on other sites More sharing options...
monstaru Posted November 2, 2004 Share Posted November 2, 2004 damn, i needed that bumper stop yeah yeah, you were right......did ya just need to hear it?i just kinda figured it was a vacuum thingy.....good job nut Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now