Turbone

Its a form of entertaiment for some. You really dont need to open the thread and read it if you dont like it. But I agree its OT material now.

For starters, at the top of the main page here is a link to the new XT6 site. Lots of info and help there. You really should have bought a different Soob:rolleyes: XT6's are very persnickety and tempermental. 1. From this question and the next, you may have more then a shifter bushing problem. I would try the "Tranny Cocktail" on it. 2. Skip this one. 3. The ER27 has a Idle Air Control valve (IAC). It will cause this problem. I think there is a procedure in the FSM for cleaning it. If not, I know theres something at the XT6 board. 4. Sounds like the brake pads need shims. This will keep the from squeeling. Or the stuff you can buy in the little pouches (blue glue). The ceramics might make it worse too. 5. Go back and look for it? 6. A stock unit should work fine. It would be a good idea to get the flywheel turned.

Well, I guess we can give him credit for being consistant:rolleyes: But thats it.

Welcome to the USMB. First of all, your engine designation is a EA82T (T for turbo). It will have the Multi Port FI. Theres a few sites out there that have all the specs on it. If the tranny is a 3spd, you may want to flush it and put new fluids in it. But I think its most likely a 4EAT, which isnt all that bad. If you have problems with it shifting or being slow, give it a flush. The cooling system is the weak link for this engine. Theres a couple of companies that sell 2 row radiators for this model, I suggest doing this. If theres oil leaks from the front of the engine, a re-seal is a good idea. That way you can replace the waterpump at the same time. There is a limit to the tire size, I believe there is a thread about it in the Offroad Forum. As for the noise, it could be whats called TOD (Tick of Death). Dont worry, its not that bad. The engine has hydraulic lash adjusters(lifters) and if the oil leaks out of them they tick/clatter until they get pumped up again. Sometimes if its a high mileage engine, sludge gets built up and blocks the oil passages to the lifters. One of the remedies is to use some Marvel Mystery Oil during a oil change. Or add some if the oil is low. I think a couple of people have done the spray on liner on thier undercarriages. Anything will help in that dept. Again, welcome.

No more EA82T project cars for me, I'm sick of doing HG's:rolleyes: Yeah, I'm a real pro at them now:-\ I have to say my last job held up real well. It blew the rim off the piston instead of blowing the HG:grin: And that one is a little to far away and it has.................rust:mad:

I got me some EA81 Brembo rotors off Ebay a few months ago. I think I paid around $50, including shipping. Still waiting to put them on my Brat:rolleyes:

Where did you buy the alternator and was it new or rebuilt? I would take it back and have them test it. Cause it sure sounds like a bad one to me.

Is that the only color you can do?

HBD.....youngin:-p

Pay for my gas and I'll do it(and maybe lunch) Have tools, will travel:-p

$90 for the 89 FSM is a little steep for me, but seems to be about right for new. I'm sure I could find it cheaper (used) on Ebay.

Ummmm, get a GF?:-p

I've worked strictly on Subaru's for the last several years (cept for the Mazda truck I traded a few years back), so I guess I'm a little spoiled.....and biased. The Mitsu's are not mech friendly, IMHO. What usually takes me less than 1hr to do (engine pull) took me a 1.5 days to do. I dont care how fast the car is supposed to be, but I do care how long it takes me to do a engine swap:rolleyes: The engine is at my place as of today and we started putting parts on it, getting it ready for the install. It has to be in by this weekend, for reasons stated below. I've got 2 SVX's to work on after this thing is gone. 2 engine/tranny pulls, with the engine/tranny reinstalled in one. I'm going to be a busy boy for a while, but it may be put on the back burner for a month:-\ Tomorrow I go in for a Eval for a 1 month intensive therapy stint. Its supposed to be 8hrs a day, 40hrs a week for 1 month:eek: I may have to take a month off just to recoup after that:rolleyes: It will be close to Winter by then and I know the weather is going to suck:mad:

Are you heading for the desert already? Summer isnt even over here yet. Or is all this sun getting to you:-p

Still waiting for the engine to come in. It was suppossed to be here this week, but they say the Holiday on Monday screwed shipping up:rolleyes:

Dont worry, its outnumbered;) Especially after today:rolleyes:

Preferably the thread from where the request/deal was made from. That way you can copy and paste the URL in the neccessary fields when leaving the FB.

All you needed to do was look in the USRM at the top right of the page:-p http://www.ultimatesubaru.org/forum/showthread.php?t=49918

The brushes are quite common. Heres a link to the thread over at XT6.net. http://subaruxt.com/forum/viewtopic.php?t=7812&highlight=brushes

Take them off and replace them with a set of rear disc. Its super easy to do and you wonter regret it. Get ahold of Baccaruda, he might have some or would be able to find you a set in Spokane. If he cant, let me know. I'll find you a set.......I grow em on a tree in my backyard:-p

Lucky dude! Thats awesome:headbang: I have a bunch of In Laws in Montegue/Shastina. May have to make a run down that way next year and stop by the Shop;)

It should burn off once you start it up again.

This just meant for the USDM it was optioned out. There were some items that had to be ordered like a LSD rear diff.

Of course its head gaskets, its a EA82T:rolleyes: Sorry, I have had several of these and its a common problem.....and a cheap way to get a Subaru:-p Along with checking the rad for bubbles while running, keep an eye on the temp. If it rises above the halfway mark, it very well could be a bad HG. Let me know if you need parts for it, I have lots and am only 45min away from you. Also go register at http://xt6.proboards50.com/index.cgi#general. Its a temp site right now until the original one gets some registration problems ironed out.

A simple search turned up this.... http://www.ultimatesubaru.org/forum/showthread.php?t=76746&highlight=ford+springs