Search the Community

HERE IS WHAT HAPPENED. Yesterday, I discovered the green connector for CEL testing has been plugged in forever. i unplugged it, and proceeded to do what I know, in order to read the check engine light. The oxygen monitor showed codes 21(coolant temp sensor), 24(idle air control valve or circuit) and 34(EGR solenoid or circuit). It got dark, so I went inside and proceeded to look online for a replacement IACV gasket, so I can clean it. I also looked at an EGR solenoid and planned on cleaning the EGR today. When I went to start my car this morning, it fired but died immediately, and I knew something was wrong. One more start and die, and without pumping the throttle or having it wide open, the car just cranked and didnt fire. What the heck? So I read the codes again, and nothing had changed. As far as I know the only thing I did was make a red light blink, so i'm a little confused. Is it possible that the car is acting up because the ECU "didnt know" about the bad egr and iacv until i put it in test mode? before having gone inside last night i started the car, and it RAN FINE. Again, what the heck? Does anyone have any ideas? car has always had idle issues, and at one point an ignition coil that arced to the negative ground. ask me questions and i will answer, but so far, thats what i got. Thank you guys in advance. -walker

Hey everyone, I've got my '92 Loyale Wagon up and going and I want to start moding it for off-road. The only thing is, I can't find places or websites to get exactly what I want. So I'm on here asking for some help. LOL. Here is a small list of what I'm trying to accomplish. First is a Snorkel, I think I can manage this with some PVC pipe and a saw. Next a nice and sturdy roof rack. Rear bumper with spare tire and jerry can holder Similar to a Jeeps Smitybilt. Suspension lift kit or custom lift. Under Engine protection plate for off-roading. Some wheels that are larger than 13" and are 4x140 lug pattern or an adapter kit. Dual exhaust or just a replacement. Mines in pieces! I think that's it for now. So can anyone help me out? Thanks SOOOOO much! -Mike

So, I bought a 1990 Loyale coupe in early January. I have to admit, though, I'm not too terribly knowledgeable about the Loyale RS, or the Loyale in general, so I'm really just looking for any info I can get on this particular car, which has been less than forthcoming on the Googles. I suppose it might help if you knew what I was planning on using it for? Autocross. More specifically, running in H Stock (for you SCCA peoples). It's a five speed, naturally aspirated with that funny push button 4WD option. If you'd be so kind, could you learn me a bit about my car?

How in the bloody hell do I uncover the rear strut towers in my 90 wagon? am trying to remove struts and put on coil sleeves. where the codswalloping codswallop is the magic button that uncovers the tops?

Hey guys! I completed my dual range swap but have some questions!! any help would be appreciated! So after my swap everything went okay,,, but eventually my clutch fork bent back,,, So my first question is: Are 4x4 clutch forks a little curved as apposed to 2wd clutch forks or did i bend it? Second what is the proper assembly for clutch forks?? i currently need to replace and have NO idea how to and my Hanes manual doesnt say how.... Car is a; 93 ,loyale, sedan, d/r swap, 5spd, 155k Thanks for any help, I can try to have pictures tomorrow.....

i was learning how to drive in this car and didnt know at the time that it had locking diffs for 4wd which make it very hard to turn on asphalt so i tried to turn into my driveway and ended up hitting a tree breaking my front left corner light(not just the lens, but the entire light). And now i cant find a replacement for the life of me.

I've got a set of EA82 turbo heads off of my 1987 GL-10 wagon. Motor lost a rod bearing in the bottom end, but there was no sign of failure from the top end. Includes intake, fuel rails, etc.... Finally did the EJ22 swap after doing one on my Vanagon, so I don't need these goodies anymore! Make me an offer, I was thinking in the neighborhood of $100. I am in the Portland area if you want to pick them up, since the cost of shipping would be atrocious.

Hello everyone, new member, purchased a '92 Loyale wagon to get us up the mountain (and our driveway) in the winter. Car was running great for the first few weeks of ownership but just lately has started to run a little erratically. So far I've cleaned the MAF sensor and have installed a new WIX brand air filter from Napa. First start in the morning it used to run at a high idle until the accelerator pedal was depressed then settled into a lower idle, which from experience is how it should run. Reversing up to the driveway and then going up the driveway it ran great, no hesitation or stalling. Now when it's started in the morning it'll run high idle for about 10 seconds and want to cut out. After about 30 seconds warm up I go to reverse and it wants to die unless I keep the revs up and ride the clutch a little. Same going up the driveway it wants to cut out and hesitates. Also when driving around town it doesn't run smoothly, there's a distinct hesitation when accelerating which dissipates somewhat if you increase the revs before changing up gears. So I'm thinking possibly fuel filter clogged or possibly the TBI injector faulty or maybe the air bleed valve or similar is not working properly? Or could it be an electrical problem? Any guidance or suggestions much appreciated.

I don't know an incredible lot about these cars, I just did an engine swap yesterday from 1991 Loyale into my 1987 GL. My '87 had almost 300,000 miles, still ran, but, it was time for a fresh motor, so, I put a 120,000 mile motor from my friend's totalled loyale in it. (It was rear ended) It started easily, ran great, accelerated easily, it was a fun little motor. But, I was driving and suddenly the motor just stopped, sputtered out. The engine was warmer than it should have been, so, I thought I might have lost head gaskets, but, no smoke, no coolant spew, and it didn't sound like I grenaded the motor. It just died and refused to start again. It turns over easily, no wierd noise or hesitation, it just won't start. I checked the oil when it died and it didn't look like milkshake (when coolant enters oil). So, I don't think it's headgaskets. I thought maybe I lost a timing belt, but, if I remove my distributor cap the distributor still rotates when I turn the engine over, which indicates timing. I know these cars have two timing belts, so, could I have lost te passenger side belt? I kind of think it would run, but, just run like spoob with half the timing. I don't know though. Anybody have any answers?

What is up everyone? I wanted to make a post of my latest swap, I started with a 1992 Loyale Wagon with a 4" lift kit homemade, 27" tires, 6 lug hubs, Datsun Turbine aluminum 14" wheels, it had a 1988 GL EA82 which ran amazing and had a surprising amount of power, it also has the dual range from an 88 GL as well, not one of those funky pushbutton deals the loyales had. On a trip back from Golden,CO to Cheyenne, WY where we moved to the EA started to knock really really bad. Maybe it was a rod, maybe it was a valve? Who cares it was a gutless EA82. So I began shopping for a donor... I found a 1990 Legacy down in fort Collins the guy had wrecked, he spun it around and slammed the rear end into a concrete barrier. Needless to say it was destroyed, I still opted to drive it all the way to my house from his though which was an hour away. The car ran awesome it just kinda leaned and drifted to the right a lot. This all started around Labor day and I just now finished yesterday, I contribute this to having a wife who is 8 months pregnant and we have a 2.5 year old boy so time was hard to come by. Also coming up with money to spend on the project is also very hard to explain to a preggo who needs things for a new baby as im sure some of you guys know haha. Anyways lets get into it, this is what I did that has worked great so far. I used the radiator from the legacy and it fit perfectly where the old one was, all I did was grind off the little metal studs that were on the bottom of the EJ rad so it would sit flat and I used my grinder to cut the sheet metal of the loyale so that the radiator would not lean into the engine, the only real issue I had was the radiator hoses but thanks to smart phones I just took a pic of the inlets/outlets and went to advance and grabbed a couple of hoses that looked like I could make work by cutting them. Thinking of it I had to cut a small piece of metal out from the inside of the hood so the rad cap wouldn't hit, worked great using the existing overflow reservoir. Exhaust: On the first swap I did I basically just bolted up the EJ header to the engine and got rid of the rest of the exhaust that bolted on with those spring bolts about middle of the car. At this junction I welded a 2" inlet 2" outlet cherry bomb then welded on a 45 degree 2" and straight out in front of the wheel tire. Makes for a badass Subaru sound and I mostly drive around with no music cause I love the way it sounds. Adapter Plate: For some reason I had it in my head SJR charged $400 for just the plate, then I wanted to look again the other day and that was for all of it including the drilled flywheel haha wow. I opted for a 16"x16" 1/2" thick plate of steel from metal distributors which ran me $90. This was just a plate mind you, I spent so many days grinding torching and welding to make it right, when I could've just paid $185. well well worth the money. The first plate I made I used 1/2" aluminum from Alreco in brighton, Colorado. Aluminum is much easier to work with that steel. I didn't have many issues with the plate at all actually and it is super strong, no issues at all so far. Wiring/Electrical: Yes, the most amazing part of the swap. If you are considering doing this swap and have never done an undertaking like this just do it stop being a wuss. Theyre just wires. On the other hand I am an elevator service tech and I deal with electricity and mechanics every day at work so it didn't bother me to dive right in as I have to read and figure out electrical systems on elevators when they break. This is what I did with my big stuff like the fuel pump relay, ignition relay, fuel pump yada yada. For the constant 12v power I used the fat white 12a going to the ignition switch in the steering column, I tapped in and then attached my own inline fuse, for the switched 12v I used the fat black 12ga wire going to the same switch, I also used an inline fuse for this as well. From there I wired up the fuel pump relay on the top as your looking down at it from the top there is a smaller green/blk wire that goes directly to F47#23 or D23 this is called Fuel Pump Control in the prints. The small yellow wire is attached to the 12V switched power that I tapped into, The blk/red wire goes to the positive side of the existing fuel pump, I tapped in the existing one that was under the dash on the pass side. the FAT yellow wire gets tapped in the 12v constant after the fuse I installed. The Ignition Relay: The light green wire, oh man this caused me many many hours of grief freezing in the garage. When you tear out the harness DO NOT disregard the diode. What is the diode you may be asking, well it is half grey and half black and has 3 wires coming out of it, I light green and 2 yellows, I disregarded this little gem at first, geez why wont this POS cranks?! Well lo and behold after doing a lot of research I found a Volkswagen wiring diagram where a guy transplanted an EJ22, that's when I saw the diode. This time I kept ALL of the wiring I removed from the legacy and with some digging I found it! With about a foot of wires sticking out of it still, I attached it with the light green wire coming off of the ignition relay with one end going to ECU point F47#5 Self Shutoff Control, one to one of the diode green wires, and one to 12V switched power. Boom that thing fired right up! Okay now to the rest of the IGN relay, the black on It goes to a ground, the 2 FAT yellows go to 12V constant and one of the FAT yellow/red wires goes to the O2 Sensor, the other FAT yellow/red goes to A2 and A13 (B48#2 B48#13) Tuning and testing: The thing would run awesome just idling, however when I drove it would backfire and sputter and buck and sneeze. Over the last 2 weeks ive been scratching my head and freezing trying to figure it out, was it a spark plug? No. Was it the plug wires? No. Oh Oh maybe a bad injector? Trying to pull one out I broke the top off...argh. another couple days later got 2 used ones, I had pulled the fuel injector next to it to compare when I went to find new ones at the junkyard, well I put the new ones back in and what do ya know it ran...terrible! spitting gas out the exhaust burning white smoke, what the hell? I pulled those two plugs and they were soaked in gas. What? Well more research and more days and random hours I found that when most people replace fuel injectors they don't pay attention to replacing the O ring which basically just allows fuel to literally pour in! I was able to get FI O rings at advance that were universal and it fixed that. Of course this 2.2 has the black top injectors and not the reds because I have 3 extra ones of those. Then came the eureka moment, after that incident I cleaned the plugs and wanted to test some more, my god it still backfires and sputters and cant hardly drive. Then the next day I figured id give it another shot and it had snowed the night before, I got in while it was warming up and turned on the wipers to get the snow off and as soon as I turned em on the car died. My head started to hurt, why did that happen? that has nothing to do with the engine! WTF. Then it hit me. Grounds. I remember attaching the ground of the ignitor and the MAF to the ground on the outside of the windshield wiper motor. Why I did this I don't know, I remember from the first swap a common ground is needed for all the grounds for less complications. Needless to say I took these ridiculous grounds off and attached a black wire and ran it to the common ground located in front of the battery. Then boom the car ran just the way I wanted, fast and loud. Holy crap what a relief! Forgive me for such a long post but I felt it was necessary and hopefully it helps some other poor sap like me someday. If you've got any questions feel free to ask, have a good one and good luck!

GOD BLESS US EVERYONE!!!! IT'S A CHRISTMAS MIRACLE!!! I love my girlfriend so much. She knows just what makes my heart beat. I guess I'm being dramatic.....but this is the happiest I've been opening a christmas gift since my first bike when I was 5 years old. Anyhow.....Here's the details....Puchased through Autozone. Sachs part # 031-168 Must look them up for either 85/86 4wd wagon w/vin 5 carbed engine. Tiny Tim won't need those crutches anymore!

I recently replaced my timing belt and pulleys, oil pump, water pump, cam seals, main seal and thermostat (thanks for the videos miles fox!) When i first started the car the passenger side timing belt pulled backwards towards the firewall on the cam pulley and is was riding pretty close to the edge of the pulley. I turned the car off and loosened the tensioner and pulled the belt back to the center of the pulley. when i started the car again the belt went immediately back to riding on the edge of the cam pulley. any ideas? Also terrible gas mileage before and after this job circa 15mpg in the city any ideas on this? edit = car is a 5mt 4wd loyale with 261k, the repair was originally initiated from a ball bearing falling out of my oil pump. thanks!

First I would like to say hello and thanks. I have been using this forum for years but this is my first post. I bought this car 2 years ago with close to 200,000 miles. I was told it had a bad MAF but when I got there to test drive it (with an untested junkyard replacement MAF) it had a huge hole in the plastic next to the MAF. I duct taped the hole and tested both MAF and got the same results (crappy but better than before duct tape). The car was throwing solenoid codes that were not MAF related...so I thought maybe she took it to a mechanic that did not understand Subaru's and mis diagnosed the MAF. The guy who said it was the MAF also missed the giant hole in the plastic. How is beyond me, but his credibility went to zero! So far I replaced: - The plastic/rubber housing that the MAF (and most vac hoses) mounts into. (whats that called) - PCV (new) - O2 Sensor (new) - 2 solenoids (EGR and purge control) - IAC - Plugs, wires, d cap (new) - MAF (junkyard) and cleaned the original - Fuel Filter (new) I also tried: - Seafoam - Alcohol and water into vacuum lines - Alcohol in the fuel PS... The alternator was brand new. First I did all of the above to clear a bunch of codes. The codes returned. I re-replaced both solenoids and IAC again (new, not junk yard this time). Codes are now gone again but the car has no change in performance. NONE. The car continued to idle poorly, surges really bad when trying to maintain a slow speed (parking lots), has a hesitation when accelerating (rpms drop when clutch is released...then after a 1-3 second delay it kicks in...it feels almost like a power band kicking in ...but it goes from crap to normal not normal to overdrive). I tried to drive the front wheels up on a curb but could not get the low end power to climb up onto it. When I start it, it usually idles between 1000-1500 sometimes between 2000-3000 and sometimes it fights to stay between 200-1000 or just dies (200-1000 is more common when warm). I have been playing with the throttle cable constantly to keep it from stalling so all of these RPM values may be irrelevant. I have found cracked vacuum hoses but no matter how many I fix nothing changes. I also removed several vacuum hoses (on purpose...as a test) but it does not get worse (removed charcoal canister, removed vac hose to pcv...one at a time...no response). It runs fine at highway speeds, gets pretty good gas mileage and starts instantly on even the coldest nights. I am at a loss! - I suspect a vacuum leak but my heater vents and 4x4 button work properly. Then again, my brakes have been acting up but introducing a major leak does not make it worse?!?!!?! - Maybe a fuel pump or sock issue. - Maybe a computer issue caused by playing with the screw on the carb (I read not to do that...it was too late) - Maybe I need a new battery (lots of corrosion on one tower) - Maybe my fuel filter got clogged instantly after replacement. - Knock sensor? IDK anything about this but it came up in other forums. - EGR...I can't get it off Random stuff that might matter: - I noticed a hose that does not go anywhere. It is a 1/2 inch hose that sticks through my passenger side firewall. It is about 9" long but does not connect to anything. It is dangling onto my exhaust pipe. Its a foot below the windshield wiper apparatus. - Charcoal canister also has a 1/2" hose on the bottom that goes nowhere (I think thats for water... is it not) - Charcoal canister has 4 nipples on the top. Only 3 have a hose connected, one is capped. If we call the 4 nipples a,b,c,d and c and d come from the riser then its a (If I'm not mistaken thats the one from the gas tank...this seems like it could be bad....No gas vapor odors though). - The lady I bought it from said she took the belt of the AC compressor - I keep hearing a clank that I suspect is a broken motor mount - Has the tick of death PS I am not a mechanic but can follow directions well enough that I do most of my own work. This is my 7th sub $1000 Subaru and I keep learning. Things like hoses, alternator, oil change, cv joints, and everything I mentioned above are easy for me. I don't have many tools or gadgets (vac or compression test stuff) but I have a muti meter. Things like clutch, tranny, head gasket mean its time to sell.

92 loyale and my 4x4x won;t engage when it press the button. recently i replaced the clutch and right after that it stopped working... thought on if that caused it to stop working? thanks!

Hey there fellow subaru lovers. ive recently started a fan page on facebook for Old Gen subarus. (it says NW but honestly we love em all!) im not really trying to post to get more likes as much as i am looking for great Old gen subaru pictures. I see amazing ones day in and day out on here and i want to use them all but i would also like to give credit to those who have made it great. i ve added a few that i absolutely couldnt help myself but id like to get more! anyone who would like to have their old gen subarus plastered on the internet with us all drooling over it either add them on this thread. send them to my email ( elliottdevon@ymail.com ) And Or go and put it on the page and like the page. https://www.facebook.com/nwoldgensubarus ALSO we have been trying to get together a meet for Old Gens in the nw most likely in the oregon area. we have a separate thread on here if you are interested. but we will likely be adding it as an event on the facebook. http://www.ultimatesubaru.org/forum/topic/142570-like-to-get-an-old-gen-meet-going-in-the-oregon-area/ Thanks all! hope to hear from you soon!

Hi there, My 1990 Loyale won't start, and it appears to be due to an electrical problem. Symptoms: Weak power to accessories when ignition is in "accessory" mode. Weaker power, and sometimes no power, when ignition is in "on" mode. Car does not start, and accessories lose power completely when ignition is in "start" mode. Testing: So far, I have done the following: checked battery voltage, checked battery connections, checked fuses, checked fusible links, tested six relays for switching and continuity (4 above the fuse box and 2 above the ECM), tested ignition switch for appropriate continuity at the different key positions, partially tested steering column switches for continuity (the diagram in the Haynes manual confuses me; nevertheless, I disconnected the steering column switches and the problem remains.) I have not noticed loose grounds or frayed wires, but perhaps I have missed some. There are a couple of interesting items to note. First, when I activate the switch for the hazard flashers, the lights do not operate and a buzzing sounds. I have disconnected the power to the flashers module, and this of course silences the buzzing sound, but the original electrical issue remains. Second, occasionally when I turn on the parking lights via the steering column switch, the needle on the tachometer jumps - this is all without the engine running! It's a mystery to me - hopefully someone out there can point me in the right direction. Thank you! Jason

Hey everyone, I am starting to prepare for rallycross. I own a 1990 5spd Loyale with an EA82. Car is stock except for Spectre cone filter, fitted to a MAF adapter(3"). Also, the drivers seat is a stock bucket seat from a Nissan 240sx, with rail adapters I made here at home. I also have mudflaps which are custom made. SO, I have a few things to do before I believe this car is ready to go sling mud around. Before anyone says anything, I am aware that this car isn't a "race-ready" vehicle, nor is it really typical for any sort of motorsport event. From what I've read about rallycross, it's about having fun and getting the car out there, not being fast and competitive. Thats what i'm looking for. I don't want to destroy the car, I want to go have fun. I have no problem driving conservatively on the track, and i'm confident that my car will do fine. I'm not out to build some badass screaming turbo race car.. I want to take a virtually stock car and improve my abilities, along with getting a feel for basic motorsports. I would assume everyone on here sees what I mean, but still, I feel like I have to say something. Alright, here is what i have in mind that should get me ready to go play. CAR -Battery tie down(i have none) -set of good tires -relocate AWD button to dash and get aftermarket shift knob -put on skidplate -fire extinguisher -straight pipe with cat ITEMS TO BUY -approved helmet -gloves -SCCA membership -gas can -tarp -jumper cables Questions: 1) Will my aftermarket seat be a problem for the inspection? Custom made adapters had to be made to make the seat fit in my car. It's sturdy, and not anything completely ridiculous. The seatbelt works and is positioned correctly. Other than what I have said, does anyone have any advice or recommendations for me? I would really appreciate it. I'm new to this, obviously. I'm a huge rally fan, and I live in the Pacific Northwest. I'll be participating in Sports Car Club of America events. I'll upload pictures of progress. Thank you guys!

I bought this Subaru about 2 weeks ago for a couple hundred bucks on a rainy dark night. Ran, shifted, and stopped just fine. Bought it and drove it around until i had to registar it. Then i started poking around. To the point: Can somebody provide me with a picture of the o2 sensor plug/location? I have been tracing wires on and off for a while and cant seem to find where the o2 sensor connects into the harness. The wires coming off of the sensor itself have definitely been cut off, but i wouldnt this they would have cut the harness as well... Im starting to wonder if the previous owner chopped it off when they swapped in a new engine. (Still an ea82 Spfi) Much appreciated.

having serious regrets about messing around w/ my Loyale, "Joan Crawlins" after i finally had her in the best shape she's been in since i got her last Winter in Penn. everything was great as stock, but then i put in a 2" inch lift to gain clearance over sand in btwn the tracks on a rutted out access road to the beach. that messed up the camber of the front wheels something awful (pics here: http://s406.photobucket.com/user/GlenSzabo/library/2%20inch%20Lift%20kit%20and%2015%20inch%20Pugs) and after tracking down some 15" alloy pugs in a junkyard in Pennsylvania and ordering lugs from Dan in Sacramento, i thought that would help the camber issue, but it didn't solve nearly enough for daily driving. so pulled the lift kit out, but kept the pugs on and had to cut a bunch of the wells out cause i was getting lots of rubbing since my suspension was in bad shape. put in new struts in the front which helped, gonna put in struts in the back in the next couple days, but having no luck finding coils for the front. CAN I USE COILS FOR ANOTHER SUBARU that are easily available? like a legacy? if so, what should i get? also, now my camber is ok in the front, i'm getting positive camber in the back, which i can only guess was as a result of putting in and taking out the lift in the back. once i put in new struts in the back and hopefully coils in the front, and then get everything aligned professionally, will my camber issues be solved, theoretically? just ruing my decision to have changed anything at this point, but all's not lost by along shot and if i can get the suspension finished and the alignment solves the camber, i'll be happy to have the Pugs on rather than the stock 13"s. here's a look at where i'm at now: http://s406.photobucket.com/user/GlenSzabo/library/Loyale%20Camber%20Issues @175eya @CoyotePaws @Mechanical_Misfit thanks for the help folks, as always, i'm eternally grateful for the advice and support. -Glen

Not sure if anyone here remembers when I last posted about my cold idle issue. Needless to say, it hasn't been fixed. I've been able to tolerate it the past few months, but now it's getting ridiculous. I've started taking auto tech classes, and my class starts at 7 am, so I have to deal with it every morning.... Please read everything carefully. Car is my '90 Loyale, EA82 N/A. The problem I have is when the car is cold, it doesn't want to idle. I start it up and have to rev it at 2000-3000 RPM for ~5 minutes before I can get it to idle at 500 or so. It's good enough to get going, so I leave. However, EVERY time I push in the clutch (or put it in neutral), the RPMs fall so fast that the engine stalls. When changing gears, this isn't a problem. But if I'm coming to a stop, I must heel-toe and feather the gas to keep it from stalling. Then, randomly, it'll idle normally. Just like if someone flipped a switch, it'll idle fine. It used to take 5 minutes or so before this happened, but now it takes up to 30 minutes!!! My school is about 30 minutes away, and sometimes I can go most of the trip there before it idles normally. Funny thing is, if I've been driving for 10 minutes or so, turn off the car, then turn it back on, it'll idle fine. For example, if I stop and get gas before school, it'll idle normally when I start it back up. The few minutes it takes to fill the tank is enough for the car to decide to idle. I know what you're thinking, it's the IACV or the CTS. I've replaced the CTS twice and the IACV twice. I've cleaned the IACV a few times, but it didn't help. The only part I've noticed that had a difference was the water pump. I swapped my longblock and it came with a new water pump on it. That water pump failed in 400 miles, but during that time, I never had an idle problem. I put my old water pump on and I soon saw the idle issue again. I've never heard of a water pump causing an idle issue, have you? Here are some of the things I've noticed: The issue doesn't seem to be related to weather much. It'll have more problems idling during the winter, but I still notice it during the summer. The issue doesn't seem to be related to how long the car has been sitting. I mean, if it's only been sitting for less than 3 hours, then it'll probably idle. But I've had it idle fine after sitting for 8 hours, and I've had it not idle at all after sitting for 4 hours. The issue doesn't seem to be related to coolant temperature. The temp gauge will reach it's normal range in a few minutes, but as stated before, sometimes it'll take 30 minutes before the car will idle. However, I believe once the temp gauge reads normal, I can turn the car off, sit for a minute, turn it back on, and it'll idle fine. In the video posted below, I took off the IACV hose with the engine running. Made no difference. Disconnected the CTS. No difference. Disconnected the IACV (electrically). No difference. I'll try the tests again with the engine warm, if that's when I'm supposed to do it. My CEL is on, but I believe it's for the purge and EGR solenoids, if I remember correctly. Been a while since I've checked; I'll check again. Anyways, any ideas? Please feel free to ask questions to help with diagnosis. Feel free to tell me any tests to do, and I'll do them (assuming I have the tools for it). When I posted this before, someone stated something about testing a pin on the connector on the ECU. I never got confirmation on what pin and what numbers I should be getting. I'm just kinda stumped as to what it could be, especially since the two most probable causes are not likely to be the problem. My gut feeling says it's an electrical problem, but I don't know where exactly to start with that. I really want to test and diagnose this, rather than doing the "shotgun" method to fixing it: throwing parts at the car hoping one will fix it. Here is the video that kinda shows the cold start. Before you say anything, the oil pressure gauge reads low; always has. And I did adjust my belts after the video. http://youtu.be/KwjWYgybeLc

Hey all, I was wondering if anyone had info on removing the stock loyale shift knob. I have already gotten the pin out, but i'm not sure how to remove the 4wd button. Inside the knob is a white plastic casing. will the casing remove from the knob, or do I have to cut the knob off around it? I am going to put the button somewhere on the dash or center console, and thread on an aftermarket shift knob. words of advice/pics much appreciated. Thank you subie family!

HEy all, I was trying to fins out is it possible to entirely swap out the ea82 engine and replace it with ANYTHING, other than an old model engine. Price is whatever, meaning if the Trans has to be new too, thats cool i just want to know about size and a secure safe fit. Thanks.

So, I own a 1990 Loyale with push button 4wd. I want to lower it using coilovers or springs(if possible) from a 90's Impreza. Does anyone have experience with this, or other bolt-on/spring swap projects? I'm not looking to cut springs, OR buy 1800 dollar coils.. Help appreciated. thanks!

I am looking for new bushings for my lower control arm in a 92 Loyale. Lordco and Napa have nothing. Any ideas where to find some? Thanks. Located in Golden, BC

Searched forums but can't find answer...I’m not very technical or mechanical(yet!).. Looking to buy Loyale and I think I found a 1993. Wondering about compatibility. I think I know the answer, it is the 88-94 subaru loyale parts are mostly compatible, right? What about 87’s and older GL’s? My long term plan is to convert to D/R 4wd and maybe engine swap down the road. I would think the lift kits and shocks are same for year range too? Thanks!